Microstructure of Bi–Cd–Sn ternary eutectic
Source abstract
Abstract
Specimens of the Bi–Cd–Sn ternary eutectic were solidified under closely controlled conditions and quenched during freezing to form a ‘quenched interface’ for subsequent observation. Very low growth rates, from 8 nm s −1 to 1·1 μm s −1 , were used to produce a microstructure sufficiently coarse to show considerable detail at the quenched interface and thus reveal distinctly the mode of solidification of the alloy. The three phases formed on solidification of this eutectic alloy are Bi, Cd, and a –;β Cd–Sn’ phase derived from the hexagonal Sn rich phase of the Cd–Sn binary system. It was observed that the Bi and Cd phases both freeze in a faceted manner whereas the β Cd–Sn phase is non-faceted. Under the growth conditions used, this eutectic showed a marked tendency to form regions of binary microstructure. At the higher growth rates examined, regions of Bi–β Cd–Sn quasiregular binary microstructure, outlined by Cd flakes, were formed, whereas at the lower growth rates the Cd and β Cd–Sn phases formed a nearly regular lamellar microstructure containing relatively large inclusions of Bi. It was observed that the Cd–Cd phase spacing varies only slowly, whereas the Bi–Bi phase spacing varies much more rapidly with growth rate in the β Cd–Sn matrix phase. This variation is attributed to the different branching tendencies of the Bi and Cd phases and appears to account for the formation of regions of binary microstructure. MST/1551
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Solidification and crystal growth phenomena · Aluminum Alloy Microstructure Properties · Metallurgical Processes and Thermodynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. KERR H. W., , PLUMTREE A., , and WINEGARD W. C.: J. Inst. Met., 1964-1965, 93, 63–64.
2. 10.1016/0022-0248(72)90025-510.1016/0022-0248(72)90025-5 ↗
3. 10.1007/BF0281136410.1007/BF02811364 ↗
4. 10.1179/mst.1986.2.6.53410.1179/mst.1986.2.6.534 ↗
5. 10.1007/BF0264402610.1007/BF02644026 ↗
6. 10.1007/BF0265841610.1007/BF02658416 ↗
7. 10.1179/mst.1986.2.10.98510.1179/mst.1986.2.10.985 ↗
8. 10.1179/03063458479042001410.1179/030634584790420014 ↗
9. COOKSEY D. J. S., and HELLAWELL A., : J. Inst. Met., 1967, 95, 183–187.
10. 10.1007/BF0265347710.1007/BF02653477 ↗
11. 10.1007/BF0266132410.1007/BF02661324 ↗
12. HOGAN L. M., , KRAFT R. W., , and LEMKEY F. D.: Adv. Mater. Res., 1971, 5, 83.
13. GUERTLER W. GUERTLER M. and ANASTASIADIAS E.: ‘A compendium of constitutional ternary diagrams of metallic systems ’ WADC Technical Report 58-615 Project No. 7351 Wright Air Development Center Wright-Patterson Air Force Base OH 1969 Part 3 p. 685.
14. GRUZLESKI J. E., and WINEGARD w. C.: Trans. Met. Soc. AIME, 1968, 242, 1785.
15. CROKER M. N., , FIDLER R. S., , and SMITH R. W.: Proc. R. Soc. (London) A, 1973, 335, 15–37.
16. RAYSON H. W., C. w. GOULDING, andG. V. amnsloa: Metallurgia, 1959,59, 125–130.
17. 10.1179/mtlr.1964.9.1.110.1179/mtlr.1964.9.1.1 ↗
18. SAVAS M. A., , CLAPHAM L., , and SMITH R. W.: J. Mater. Sci., 1990, 25, 909–913.
19. FISCHER D. J. and KURTZ w.: Acta Metall. 1980 28 777–794.10.1016/0001-6160(80)90155-8 ↗