journal article·2025-12

Study on shot peening strengthening 42CrMoA steel and its fretting wear properties

Zhiyuan Wang, Xuefeng Yang, Zhiqiang Zhang, Yeqi Zhu, Fei Song, Wenlong Dong, Min Wu

Materials Science and Technology· Volume 41· Issue 18
Publisher page

Abstract

In order to improve the tribological properties of 42CrMoA steel, it was shot peened using different parameters. The surface morphology, residual stresses, hardness, and micromotor properties of the treated specimens were thoroughly evaluated. The results showed that it led to substantial plastic deformation, increased surface roughness, grain refinement, and introduction of residual compressive stresses. In addition, a significant increase in microhardness and depth of hardened layers on the specimen surfaces was observed. Furthermore, a positive correlation between the effect of the shot peening process and the peening duration was observed. As revealed by the investigation, the shot peening process not only advances the wear resistance of the specimens but also leads to a reduced wear volume compared to untreated specimens. Furthermore, this treatment triggers a shift in the wear mechanism from the predominant occurrence of severe adhesive wear, fatigue wear, and abrasive wear in untreated specimens to a predominant mode of abrasive wear, accompanied by a minor occurrence of adhesive wear.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Surface Treatment and Residual Stress · Mechanical stress and fatigue analysis · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

University of Jinan

Shandong Xinheyuan Heat Transfer Technology Co., Ltd, China

References (24)

Show source-provided references
1. Hong J. A Semi-analytical load distribution model of spline joints[D]. The Ohio State University, 2015.
2. Yuzhong W, Yilong L, Cunhong Y, et al. Analysis of factors affecting the wear failure of an aeroengine spline pair and evolution mechanism of the tribolayer[J]. Eng Fail Anal 2023; 146.
3. Liaoyuan C, Yu Z, Xin C, et al. Repair of spline shaft by laser-cladding coarse TiC reinforced Ni-based coating: Process, microstructure and properties[J]. Ceram Int 2021; 47.
4. Shi Y, Li Y, Liu J, et al. Investigation on the parameter optimization and performance of laser cladding a gradient composite coating by a mixed powder of Co50 and Ni/WC on 20CrMnTi low carbon alloy steel[J]. Opt Laser Technol 2017.
5. 10.1051/matecconf/20192980011710.1051/matecconf/201929800117 ↗
6. Tianyang X, Hua Z, Yanjing Z, et al. Effects of pulse voltage on microstructure and properties for Si-DLC films on internal spline tooth [J]. China Surf Eng 2022; 35: 257–265.
7. Shouxi W, Dezhi W, Jun L, et al. Status quo analysis on technology and equipment of shot blasting and peening in China [J]. China Foundry Machinery Technol 2009; 264: 6–10.
8. Hongzhi Y, Pengfei Z, Zhi C, et al. Effect of shot peening on the surface properties and wear behavior of heavy-duty-axle gear steels[J]. J Mater Res Technol 2022; 17.
9. Pengtao G, Fulong C, Jianqin S, et al. Recent situation and development trend of shot peening on surface integrity [J]. Aeronaut Manuf Technol 2016; 515: 16–21.
10. Renzhi W, Xiangbin L, Yuanfa Y, et al. Investigation on microstructure in shotpeening surface straining layer of materials [J]. J Aeronaut Mater 1981; 1: 30–38+101–102.
11. 10.1016/j.ijfatigue.2016.09.01310.1016/j.ijfatigue.2016.09.013 ↗
12. 10.1016/j.msea.2011.01.07710.1016/j.msea.2011.01.077 ↗
13. Guobin L, Delin G, Mingxing Z. Friction and wear properties of medium carbon steel by means of surface nanocrystallization in dry sliding [J]. Tribology 2008; 28: 39–43.
14. 10.1557/jmr.2014.32310.1557/jmr.2014.323 ↗
15. Ping W, Liqiu H, Xiancheng S. Study on wear property of compressor shaft treated by shot peening [J]. Mech Engineer 2014; 12: 256–258.
16. 10.1016/j.surfcoat.2016.12.03710.1016/j.surfcoat.2016.12.037 ↗
17. 10.1016/j.surfcoat.2018.11.04310.1016/j.surfcoat.2018.11.043 ↗
18. Fu Z. The study on properties of laser-MAG hybrid welding with beam oscillation on 42CrMoA medium carbon quenched and tempered steel [D]. Beijing: China Academy of Machinery Science and Technology, 2016.
19. Wenbo L. Analysis and research on wear resistance and corrosion resistance of shield machine cutter ring by shot peening strengthen [D]. Beijing: University of Jinan, 2021.
20. 10.1016/0043-1648(95)90168-X10.1016/0043-1648(95)90168-X ↗
21. 10.1115/1.283247710.1115/1.2832477 ↗
22. Shengguan Q, Guanghong W, Wenlong L, et al. Fretting wear of a high-performance plasma nitrided steel[J]. Tribology 2012; 32: 486–492.
23. 10.1016/j.surfcoat.2016.09.06710.1016/j.surfcoat.2016.09.067 ↗
24. Haidi Q. Research on shot peening strengthening mechanism and tribological and contact fatigue performance of new type steel for shaft [D]. Guangdong: South China University of Technology, 2020.