journal article·2007-03

Fatigue of continuous cast AA5754 Al alloy sheet

J. X. Li, X. Y. Wen, C.-S. Man, T. Zhai

Materials Science and Technology· Volume 23· Issue 3
Publisher page

Abstract

The continuous casting technology is a cost effective way to produce aluminium alloy sheet. As a result, aluminium alloys produced by this technology have great potentials to substitute steel in autobody panel applications. In the present work, fatigue tests were carried out on hot band (in as received and heat treated conditions) of a continuous cast AA 5754 aluminium alloy (4 mm thick) in directions of 0, 45 and 90° relative to the rolling direction. S–N curves of the alloy were measured in these directions. The alloy was produced using a twin belt continuous caster. The heat treatment on the alloy was conducted using both a batch anneal furnace at a slow heating rate (0·01°C s−1) and an induction heater at a fast heating rate (116°C s−1). The effects of heating/cooling rates during heat treatment on the fatigue anisotropy were studied in the alloy. It was found that induction heat treatment at 465°C greatly improved the tensile isotropy and reduced the fatigue anisotropy in this alloy.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Platek S.: Proc. 128th Annual Meeting Light metals ‘99, San Diego, CA, USA, 28 February-4 March 1999, TMS,939–944.
2. Yu X. F., Zhao Y. M., Wen X. Y., and Zhai T.: Mater. Set Eng. A, 2005, A394, (1-2),376–384.10.1016/j.msea.2004.11.060 ↗
3. Liu W. C. · Ser. Mater · 2004 · 51 · 83
4. Gallerneault M., and Lloyd D.: Metall Ital. 2002, 94, (1), 15–18.
5. Li Z. · JOM · 2004 · 56 · 287
6. Friedman P. A., and Sherman A. M.: in ‘Automotive alloy II’, (ed.Das S. K.), 147-160; 1998, San Antonio, TX, TMS.
7. Gallerneault M., and Lloyd D.: Mater. Sci. Forum, 2002, 396-402,95–100.10.4028/www.scientific.net/MSF.396-402.95 ↗
8. 10.1179/02670830222500360410.1179/026708302225003604 ↗
9. Butuc M. C., Grácio J. J., Duarte J. Ferreira, and Rocha A. Barata da: Proc. Cong. IDDRG ‘98, Brussels, Belgium, June 1998, IDDRG,489–496.
10. 10.1007/s11661-003-0014-310.1007/s11661-003-0014-3 ↗
11. Spencer K., Corbin S. F., and Lloyd D. J.: Mater. ScL Eng. A, 2002, A322,81–90.10.1016/S0921-5093(01)01708-7 ↗
12. Gimple J. L., Wilkinson D. S., Embury J. D., and Lewandowski J. J.: in ‘Aluminum 2001: proceedings of the TMS 2001’, (ed.Das S. K. et al), 17-29; 2001, Warrendale, PA, TMS.
13. Fuller C. B., Krause A. R., Dunand D. C., and Seidman D. N.: Mater. ScL Eng. A, 2002, A338,8–16.10.1016/S0921-5093(02)00056-4 ↗
14. Suresh S. ‘Fatigue of materials’, 17; 2001, Cambridge, Cambridge University Press.
15. Wen X. Y., Liu W. C., Zhai T., Liu J., Cheng X. M., Das S. K., and Morris J. G.: Proc. Symp. on ‘Automotive alloys and aluminum sheet and plate rolling and finishing technology’, Seattle, WA, USA, February 2002, TMS,219–228.
16. Saeter J. A., and Nes E.: Mater. Sci. Forum, 1998, 273-275,477–482.10.4028/www.scientific.net/MSF.273-275.477 ↗
17. Somerday M., and Humphreys F. J.: Mater. Sci. Forum, 2000, 331-337,703–714.10.4028/www.scientific.net/MSF.331-337.703 ↗
18. Sjolstad K. · Mater. ScL Forum · 2002 · 408
19. 10.1016/j.scriptamat.2004.10.00310.1016/j.scriptamat.2004.10.003 ↗
20. Nes E., Ryum N., and Hunderi O.: Acta Metall. 1985, 33, 11.10.1016/0001-6160(85)90214-7 ↗
21. Humphreys F. J., and Hatherly M. ‘Recrystallization and related annealing phenomena’, 2nd edn; 2004, Oxford, Elsevier.10.1016/B978-008044164-1/50016-5 ↗
22. ‘Metals handbook’, Vol. 19; 1998, Materials Park, OH, ASM International.
23. Li J., Li J. X., and Zhai T.: to be submitted to Mater. Sci. Eng. A.
24. Stoloff N. S., and Duquette D. J.: CRC Grit. Rev. Solid State Set, Sep. 1974, 615–687.10.1080/10408437308245845 ↗
25. Schijve J. ‘Fatigue of structures and materials’: 2001, Dordrecht, Kluwer Academic Publisher.
26. Zhai T., Wilkinson A. J., and Martin J. W.: Mater. ScL Forum, 2000, 331-337, 1549.10.4028/www.scientific.net/MSF.331-337.1549 ↗
27. Venkateswara Rao K. T., Piascik R. S., Gangloff R. P., and Ritchie R. O.: Proc. 5th Conf. on ‘Al-Li alloys’, (ed. T. H. Sanders, Jr and E. A. Starke, Jr), 955; 1989, Birmingham, UK, MCEP.
28. 10.1016/0036-9748(86)90195-X10.1016/0036-9748(86)90195-X ↗
29. Hirsch J., and Lucke K.: Acta Metall. 1985, 33, 1927–1938.10.1016/0001-6160(85)90015-X ↗
30. Liu W. C., Zhai T., and Morris J. G.: Mater. ScL Eng. A, 2003, A358,84–93.10.1016/S0921-5093(03)00264-8 ↗