journal article·2012-03

Effect of temperature on impact properties and microstructural evolution of twinning induced plasticity steel

D Z Li, Y H Wei, L F Hou, G D Chu

Materials Science and Technology· Volume 28· Issue 3
Publisher page

Abstract

The Charpy V notch impact toughness of twinning induced plasticity steels was investigated at 20, −50, −80, −110 and −196°C. The fracture morphologies were analysed by scanning electron microscopy. The microstructural characteristic near the fractures is investigated by optical microscopy, X-ray diffraction and transmission electron microscopy. The impacted twinning induced plasticity steels exhibit better impact toughness due to the simultaneous generation of deformation twins and martensite, which hinders crack propagation and does not display ductile to brittle transition. The ruptures exhibit cleavage characteristic, and traces of deformation twins can be observed in the cleavage facets, so the cracks should propagate through the deformation twin, martensite and grain. The martensite transformation occurs because of the intensive high rate force with rapidly changing direction. The nucleation and growth of deformation twins are accomplished by the pile-up of dislocations at the positions of stress concentration, and the stacking fault grows through the moving and vanishing dislocation.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

College of Materials and Engineering, Taiyuan University of Technology, Taiyuan 030024, China

College of Materials and Engineering, North University of China, Taiyuan 030051, China

References (30)

Show source-provided references
1. 10.1016/j.msea.2007.02.07410.1016/j.msea.2007.02.074 ↗
2. Grassel O · J. Phys. IV · 1997 · 5 · 393
3. 10.1016/S0749-6419(00)00015-210.1016/S0749-6419(00)00015-2 ↗
4. 10.1016/j.msea.2007.08.07910.1016/j.msea.2007.08.079 ↗
5. 10.1016/j.msea.2008.01.00810.1016/j.msea.2008.01.008 ↗
6. 10.1016/j.scriptamat.2009.04.03810.1016/j.scriptamat.2009.04.038 ↗
7. 10.1016/j.msea.2009.08.02210.1016/j.msea.2009.08.022 ↗
8. 10.1016/j.scriptamat.2009.03.04410.1016/j.scriptamat.2009.03.044 ↗
9. 10.1016/j.actamat.2003.12.04010.1016/j.actamat.2003.12.040 ↗
10. 10.1016/j.scriptamat.2007.02.02810.1016/j.scriptamat.2007.02.028 ↗
11. 10.1016/j.msea.2008.12.05510.1016/j.msea.2008.12.055 ↗
12. Kang S · Mater. Sci. Eng. A · 2009 · 527 · 74510.1016/j.msea.2009.08.048 ↗
13. 10.1016/j.matchar.2009.11.01310.1016/j.matchar.2009.11.013 ↗
14. 10.1016/S1006-706X(09)60015-710.1016/S1006-706X(09)60015-7 ↗
15. 10.1016/S1006-706X(10)60116-110.1016/S1006-706X(10)60116-1 ↗
16. 10.1016/j.actamat.2010.05.04910.1016/j.actamat.2010.05.049 ↗
17. ASTM: ‘Annual book of ASTM standards’, ASTM Designation, E8 and E23, Vol. 03.01, 142; 1995, Philadelphia, PA, ASTM.
18. 10.1016/j.msea.2008.05.02210.1016/j.msea.2008.05.022 ↗
19. 10.1016/j.msea.2007.04.12210.1016/j.msea.2007.04.122 ↗
20. 10.1016/S0921-5093(00)00888-110.1016/S0921-5093(00)00888-1 ↗
21. 10.1016/j.msea.2010.05.01510.1016/j.msea.2010.05.015 ↗
22. Ogawa K · ASTM Spec. Tech. Publ. · 1984 · 833 · 393
23. 10.1016/j.engfracmech.2010.02.01910.1016/j.engfracmech.2010.02.019 ↗
24. 10.1016/j.msea.2006.12.17010.1016/j.msea.2006.12.170 ↗
25. 10.1016/j.msea.2004.01.06010.1016/j.msea.2004.01.060 ↗
26. 10.1016/j.matchar.2009.11.01310.1016/j.matchar.2009.11.013 ↗
27. 10.1016/j.commatsci.2006.12.01110.1016/j.commatsci.2006.12.011 ↗
28. 10.1073/pnas.061109710410.1073/pnas.0611097104 ↗
29. 10.1179/174328008X27779510.1179/174328008X277795 ↗
30. 10.1016/0001-6160(73)90085-010.1016/0001-6160(73)90085-0 ↗