journal article·2005-10Open access

Precipitation and dissolution of carbides in low alloy ductile iron plates of varied thickness

M. Caldera, G. L. Rivera, R. E. Boeri, J. A. Sikora

Materials Science and Technology· Volume 21· Issue 10

Abstract

The present work has investigated the feasibility of achieving carbide free microstructures in low alloy thin wall ductile iron (TWDI) after dissolution heat treatments. Studies were conducted using low alloy and unalloyed hypereutectic irons, obtained from thin and regular thickness blocks, cast using sand moulds. The amount of carbides present in the microstructure was measured before and after annealing heat treatments carried out at temperatures ranging between 870 and 930uC. As cast specimens contained up to 30 vol.-% of carbides. The results show that annealing heat treatments dissolved more than 90% of as cast carbides present in thinner wall specimens, while dissolution was below 30% for 13 and 25 mm Y block specimens. Chemical microanalysis demonstrated that the content of carbide stabilising elements in the carbides increased as the cooling rate during solidification diminished. Therefore, carbides present in irons solidified at a slower cooling rate are more difficult to dissolve by annealing.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. 10.1179/02670830322500944510.1179/026708303225009445 ↗
2. Rivera G. · Int. J. Cast Met. Res · 1999 · 11 · 53310.1080/13640461.1999.11819329 ↗
3. Javaid A. · AFS Trans · 1995 · 103 · 135
4. Hayrynen K. · AFS Trans · 1989 · 97 · 747
5. R. Gundlach, J. Janowak, S. Bechet and K. Rohrig: Proc. Symp. Materials Research Society Symp. Proc. (ed. H. Fredriksson and M. Hillert), Vol. 34, 251–261; 1985, New York, North-Holland.10.1557/PROC-34-399 ↗
6. H. Fredriksson and I. Svensson: Proc. Symp. Materials Research Society Symp. Proc. (ed. H. Fredriksson and M. Hillert), Vol. 34, 273–284; 1985, New York, North-Holland.10.1557/PROC-34-273 ↗
7. H. Fredriksson: in ‘Advanced materials research’, (ed. G. Lesoult and J. Lacaze), Vol. 4 –5, 505; 1997, Aedermannsdorf, Switzerland, Scitec Publications.10.4028/www.scientific.net/AMR.4-5.505 ↗
8. L. Nastac and D. Stefanescu: in ‘Advanced materials research’, (ed. G. Lesoult and J. Lacaze), Vol. 4 –5, 469; 1997, Aedermannsdorf, Switzerland, Scitec Publications.10.4028/www.scientific.net/AMR.4-5.469 ↗
9. 10.2355/isijinternational.41.98610.2355/isijinternational.41.986 ↗
10. 10.1016/S1359-6454(99)00233-510.1016/S1359-6454(99)00233-5 ↗
11. Lacaze J. · J. Cast Met. Res · 2003 · 16 · 16710.1080/13640461.2003.11819577 ↗
12. Torres Camacho G. · J. Cast Met. Res · 2003 · 16 · 17310.1080/13640461.2003.11819578 ↗
13. M. Caldera, J. Massone, R. Boeri and J. Sikora: Proc. Conf. SAM–CONAMET–AAS, Posadas, Argentina, September 2001, 75–82.
14. Rivera G. · Cast Met · 1995 · 8 · 110.1080/09534962.1995.11819186 ↗
15. Massone J. · Int. J. Cast Met. Res · 2003 · 16 · 17910.1080/13640461.2003.11819579 ↗