Effect of isothermal temperature and load on wear of nanobainitic cast steel
Source abstract
Abstract
The wear behaviour of a nanobainitic cast steel: 0.76C-2.08Si-0.74Mn-0.79Cr (wt. %), isothermally treated at different temperatures, 250 and 300°C; have been investigated by pin on disk test in dry conditions. The tests were carried out at different loads: 2, 7, 12 and 15 N. The results show that the wear rate is higher when the isothermal transformation temperature and load increases. Also, at low loads adhesion, oxidation and abrasion are the main wearing mechanisms, while at high loads contact fatigue becomes dominant. The results are related to the microstructural differences produced by the change in the isothermal temperature of the heat treatment.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Gipimme, Department of Materials Engineering, Universidad de Antioquia, Medellin, Colombia
References (35)
Show source-provided references
1. Garcia-Mateo C · 2016 · 315
2. Garcia-Mateo C · 2017 · 707
3. 10.1179/1743284714Y.000000074510.1179/1743284714Y.0000000745 ↗
4. Kankanala A, Leiro A, Vourinen E, et al. The tribological behaviour under rolling/sliding conditions bainitic steel austempered at diferent temperatures. In: Proceedings of the 14th Nordic Symposium on Tribology: NORDTRIB 2010, 2010 June 8–11, Storforsen, Sweden, vol. 273, no. 1, pp. 2–8.10.1016/j.wear.2011.03.025 ↗
5. 10.1016/j.wear.2004.09.06410.1016/j.wear.2004.09.064 ↗
6. 10.1080/02670836.2015.113204810.1080/02670836.2015.1132048 ↗
7. 10.1080/02670836.2016.115730010.1080/02670836.2016.1157300 ↗
8. 10.1179/1743284713Y.000000024210.1179/1743284713Y.0000000242 ↗
9. Ríos-Diez O · 2020
10. 10.1007/s40962-020-00512-410.1007/s40962-020-00512-4 ↗
11. 10.3390/met1102022010.3390/met11020220 ↗
12. 10.3390/met1005061210.3390/met10050612 ↗
13. 10.3390/met1005063510.3390/met10050635 ↗
14. 10.1016/S0043-1648(96)07411-X10.1016/S0043-1648(96)07411-X ↗
15. Buschow KHJ · 2001 · 1
16. 10.1016/j.surfcoat.2008.02.01310.1016/j.surfcoat.2008.02.013 ↗
17. Leiro A · 2014
18. 10.1080/02670836.2016.124523910.1080/02670836.2016.1245239 ↗
19. Voigt R · Trans Am Foundrymen’s Soc · 1986 · 11 · 151
20. 10.1016/j.jmrt.2021.01.09410.1016/j.jmrt.2021.01.094 ↗
21. 10.1080/02670836.2018.150712410.1080/02670836.2018.1507124 ↗
22. 10.1016/j.matchar.2016.10.02310.1016/j.matchar.2016.10.023 ↗
23. Dyson D, Holmes B. Effect of alloying additions on the lattice parameter of austenite, J Iron Steel Inst 1970; 208: 469–474.
24. 10.1007/s11665-019-04178-w10.1007/s11665-019-04178-w ↗
25. Bhadeshia HKDH · 2001
26. 10.1016/j.actamat.2015.03.01810.1016/j.actamat.2015.03.018 ↗
27. 10.1179/174328406X8612810.1179/174328406X86128 ↗
28. 10.1007/BF0265830910.1007/BF02658309 ↗
29. 10.1179/02670830422501118010.1179/026708304225011180 ↗
30. Gwidon WS · 2005
31. 10.1016/0001-6160(87)90016-210.1016/0001-6160(87)90016-2 ↗
32. Howard EB · 1975
33. 10.1016/j.wear.2012.11.06410.1016/j.wear.2012.11.064 ↗
34. 10.1007/s11661-021-06266-w10.1007/s11661-021-06266-w ↗
35. 10.1016/j.jmrt.2020.01.05210.1016/j.jmrt.2020.01.052 ↗