journal article·2023-07

Effect of welding speed on microstructural and mechanical properties of EB Ti-15V-3Al-3Cr-3Sn welds

K. Vamsi Krishna, M. K. Talari, Bharath Bandi, Sriharitha Rowthu, M. I. Khan, P. Mastanaiah, N. Kishore Babu

Materials Science and Technology· Volume 39· Issue 11
Publisher page

Abstract

In the current study, the influence of welding speed (500, 700 and 800 mm/min) and post-weld heat treatment (PWHT) on microstructure and mechanical properties of electron beam welded Ti-15V-3Al-3Cr-3Sn was systematically studied. The welds at 800 mm/min welding speed showed higher ultimate tensile strength (UTS) (751 MPa), and hardness (245 HV) compared to welds prepared with 500 mm/min welding speed (UTS 670 MPa; hardness 235 HV). The higher strength at 800 mm/min welding can be attributed to the lower columnar width of β grains and the formation of equiaxed grains at the weld root and centre. A significant increase in UTS and hardness values was observed in samples subjected to the post-weld heat treatment (PWHT) for all the weld speeds.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Metal and Thin Film Mechanics · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Metallurgical and Materials Engineering, National Institute of Technology Warangal, Warangal, Telangana, India

Warwick Manufacturing Group (WMG), University of Warwick, Coventry, UK

Materials Engineering, Indian Institute of Technology Gandhinagar, Gandhinagar, Gujarat, India

Defence Research and Development Laboratory, Hyderabad, Telangana, India

Funding

Aeronautics Research and Development Board

References (29)

Show source-provided references
1. 10.1007/s00170-017-1169-110.1007/s00170-017-1169-1 ↗
2. 10.4028/www.scientific.net/MSF.546-549.141310.4028/www.scientific.net/MSF.546-549.1413 ↗
3. 10.1016/j.msea.2015.12.01310.1016/j.msea.2015.12.013 ↗
4. 10.1016/j.matdes.2014.11.00410.1016/j.matdes.2014.11.004 ↗
5. 10.1007/BF0333916510.1007/BF03339165 ↗
6. 10.1016/j.ijfatigue.2014.12.00510.1016/j.ijfatigue.2014.12.005 ↗
7. 10.1016/j.msea.2007.03.04010.1016/j.msea.2007.03.040 ↗
8. 10.1016/0261-3069(85)90009-310.1016/0261-3069(85)90009-3 ↗
9. 10.1016/j.matchemphys.2010.12.01910.1016/j.matchemphys.2010.12.019 ↗
10. 10.1016/j.proeng.2013.08.20210.1016/j.proeng.2013.08.202 ↗
11. 10.1016/j.jmatprotec.2012.06.02310.1016/j.jmatprotec.2012.06.023 ↗
12. 10.1016/S1003-6326(09)60381-210.1016/S1003-6326(09)60381-2 ↗
13. 10.1007/s11661-009-9952-810.1007/s11661-009-9952-8 ↗
14. Becker DW · Weld J · 1980 · 124 · 85
15. 10.1016/j.jallcom.2014.03.18310.1016/j.jallcom.2014.03.183 ↗
16. 10.1007/s11665-020-05445-x10.1007/s11665-020-05445-x ↗
17. 10.1520/JTE2020007810.1520/JTE20200078 ↗
18. 10.1080/0950711940954853610.1080/09507119409548536 ↗
19. 10.1016/j.jallcom.2018.03.28610.1016/j.jallcom.2018.03.286 ↗
20. 10.1016/j.actamat.2019.02.02010.1016/j.actamat.2019.02.020 ↗
21. 10.1016/s0921-5093(98)01010-710.1016/s0921-5093(98)01010-7 ↗
22. 10.1179/174329305X5747310.1179/174329305X57473 ↗
23. 10.1007/bf0262839210.1007/bf02628392 ↗
24. 10.3139/147.11009710.3139/147.110097 ↗
25. 10.1016/j.actamat.2003.11.00310.1016/j.actamat.2003.11.003 ↗
26. ASM. Chapter 1: weld solidification. Weld Integr Perform. 1997;6:417.
27. 10.1051/matecconf/20171230000110.1051/matecconf/201712300001 ↗
28. 10.1007/s12666-016-0985-610.1007/s12666-016-0985-6 ↗
29. 10.1179/13621710422502159910.1179/136217104225021599 ↗