journal article·2012-01

Effect of phase transformation and indium addition on workhardening characteristics of Al–Zn alloy

A M Abd El-Khalek

Materials Science and Technology· Volume 28· Issue 1
Publisher page

Abstract

Tensile characteristics of both Al–10Zn and Al–10Zn–0·2In (wt-%) alloys were investigated in the temperature range from 413 to 473 K. The workhardening coefficient, the yield stress, the fracture stress, resilience, toughness and fracture time generally decrease with increasing deformation temperature. On the other hand, the fracture strain and dislocation slip distance increased with increasing deformation temperature. The two observed temperature regions around the transformation temperature (443 K), which characterise the magnitude of variation of these parameters point to two fracture mechanisms activated with 23·2 and 49·4 kJ mol−1 for the low and high temperature regions respectively. Indium addition caused general increase for all the measured strength parameters. The microstructures of the samples under investigation have been examined after stress–strain deformation by X-ray diffraction analysis.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Physics Faculty of Education, Ain Shams University, Cairo, Egypt

References (26)

Show source-provided references
1. 10.1016/S0921-4526(00)00498-110.1016/S0921-4526(00)00498-1 ↗
2. 10.1016/0025-5416(77)90222-110.1016/0025-5416(77)90222-1 ↗
3. 10.1016/0042-207X(95)00017-810.1016/0042-207X(95)00017-8 ↗
4. 10.1016/j.msea.2007.05.07110.1016/j.msea.2007.05.071 ↗
5. Youssef SB · Acta Phys. Slov. · 1993 · 43 · 431
6. 10.1002/crat.217030072610.1002/crat.2170300726 ↗
7. 10.1016/S0921-4526(03)00318-110.1016/S0921-4526(03)00318-1 ↗
8. Abd El-Salam F, Mostafa MT, Nada RH, Abd El-Khalek AM: Phys. Status Solidi A, 2001, 185A, 2 331.10.1002/1521-396X(200106)185:2<331::AID-PSSA331>3.0.CO;2-4 ↗
9. Mostafa MM · Ain Shams Sci. Bull. · 1991 · 29 · 32
10. 10.1002/pssa.221144011210.1002/pssa.2211440112 ↗
11. 10.1016/j.msea.2007.04.02310.1016/j.msea.2007.04.023 ↗
12. Entwistle KM · J. Inst. Met. · 1966 · 94 · 2335
13. Abd El-Salam F · Fizika A · 2001 · 10 · 73
14. 10.1179/174328407X21312510.1179/174328407X213125 ↗
15. Murray JL, McAlister AJ: In ‘ASM handbook’, Vol. 3, ‘Alloy phase diagrams’, 56; 1983, Materials Park, OH, The Information Society.
16. 10.1016/j.jallcom.2007.05.05510.1016/j.jallcom.2007.05.055 ↗
17. 10.1016/j.msea.2009.08.00210.1016/j.msea.2009.08.002 ↗
18. Mott NF · Trans. Metal. Soc. AIME · 1960 · 218 · 6
19. Kittel C: ‘Introduction to solid state physics’, 85; 1984, New Delhi, Wiley Eastern Ltd.
20. Fawzy A, Nada RH: Physica B, 2006, 371B, 5–11.10.1016/j.physb.2005.08.045 ↗
21. 10.1016/0025-5416(77)90222-110.1016/0025-5416(77)90222-1 ↗
22. 10.1016/0001-6160(60)90186-310.1016/0001-6160(60)90186-3 ↗
23. 10.1007/BF0160510210.1007/BF01605102 ↗
24. Friedel J: ‘Dislocations’, 265; 1964, Oxford, Pergamon Press.10.1016/B978-0-08-013523-6.50011-9 ↗
25. 10.1023/A:100455911565810.1023/A:1004559115658 ↗
26. 10.1002/(SICI)1521-396X(199808)168:2<389::AID-PSSA389>3.0.CO;2-O10.1002/(SICI)1521-396X(199808)168:2<389::AID-PSSA389>3.0.CO;2-O ↗