journal article·2012-11

Mg bearing coating of resin sand–PTSA moulds to control graphite degeneration in surface layer of ductile iron castings

N Ivan, M Chisamera, I Riposan

Materials Science and Technology· Volume 28· Issue 11
Publisher page

Abstract

The relative performance of coatings for furan resin sand (FRS)–P-toluol sulphonic acid (PTSA) mould (FRS–PTSA), compared with no S, Novolak resin sand coated mould (NRS) was evaluated to determine the occurrence of a degenerated graphite surface layer. The FRS–PTSA moulds evidently incited graphite degeneration in the surface layer, as its thickness increased up to 10 times that with NRS moulds. Applying a mould coating containing S aggravated graphite degeneration. Conversely a desulphurising coating could protect the nodular graphite and limit the surface layer thickness. Independently of the S source at the metal/mould interface, sulphur affected graphite degeneration drastically. The coatings incorporating desulphurisation materials, [MgO; (CaO+MgO+Talc); Mg–FeSi] protected the iron from graphite degeneration, with the average layer thickness decreasing from 3·8 to 4·2: a factor of 7–10 reduction in FRS–PTSA moulds. If the first two coatings acted mainly as desulphurisers, the Mg–FeSi coating had an additional role to desulphurisation and provided Mg for the molten iron, to restore some nodularising potential. It is important to combine desulphurisation with supplementary Mg to remove migrating S and restore lost Mg. This complex behaviour could be realised by the application of coatings with active Mg from fine sized Mg–FeSi.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Politehnica University of Bucharest Bucharest, Romania

References (26)

Show source-provided references
1. 10.1016/S1007-0214(08)70028-210.1016/S1007-0214(08)70028-2 ↗
2. Riposan I · China Foundry · 2010 · 7 · 163
3. Riposan I, Chisamera M, Stan S: Submitted to Int. J. Metalcast. 2012.
4. Dix LP · AFS Trans. · 2003 · 111 · 895
5. 10.1080/13640461.2003.1181960110.1080/13640461.2003.11819601 ↗
6. Aufderheide RC · AFS Trans. · 2005 · 113 · 567
7. 10.1007/BF0335542410.1007/BF03355424 ↗
8. 10.1007/BF0335543310.1007/BF03355433 ↗
9. Boonmee S, Stefanescu DM: Proc. Carl Loper Cast Iron Symp. Madison, WI, USA, May 2009, AFS, 138–144.
10. Boonmee S, Stefanescu DM: Proc. 114th AFS Metalcast. Cong. Orlando, FL, USA, 2010, AFS, Paper 10–067, Paper 10–068.
11. Xiaogan H · AFS Trans. · 1992 · 100 · 9
12. Baier J, Koppen M: ‘Manual of casting defects’, ‘Incidence and avoidance of defects attributable to molding sands’, 32–35; 1994, Marl, IKO-Erbsloh.
13. Golovan NA · Liteinoe Proizvodstvo · 1977 · 35
14. Marti F · AFS Trans. · 1979 · 87 · 221
15. Bauer W: Giesserei – Praxis, 1982, 175.
16. Morita S, Inoyama N: Proc. Int. Foundry Cong., Kyoto, Japan, October 1968, Paper 41.
17. G. F. Balandin: “The Fundaments of Castings Moulding (Part I)”�, 327; 1976, Moscow, Maschinostroenie.
18. Leca A, Prisecaru I: “Thermophysical and Thermodynamical Properties”; 1994, Bucharest, Editura Tehnica.
19. Ivan N: “Research on the Graphite Degeneration Phenomenon in the Superficial Layer of the Iron Castings with Compact Graphite Forms”, PhD Thesis, Politehnica University of Bucharest, Romania (2011).
20. Ivan N, Chisamera M, Riposan I: Submitted to Int. J. Metalcast. 2012.
21. Riposan I · 1991, (9-10), 155–162; Casting, Forging and Heat Treatment (Japan) · 1993 · 17
22. Chisamera M · Publications · 1997 · 4 · 293
23. Chisamera M · AFS Trans. · 1996 · 104 · 581
24. Chisamera M, Riposan I, Stan S, Barstow M: Proc. AFS Cast Iron Inoculation Conference, Rosemont, IL, USA, April, 1998, Paper no. 3.
25. Chisamera M · 2002, 110, 851–860; Giesserei-Praxis · 2005 · 31
26. Chisamera M, Riposan I, Stan S, Barstow M, Kelly D, Naro R: AFS Trans. 2003, 111, Paper 03-093.