journal article·2011-01

Dual phase versus CMn strip steels: Comparison of quasi-static and dynamic connection properties for road safety barriers

D. A. F. Bayton, G. Fourlaris

Materials Science and Technology· Volume 27· Issue 1
Publisher page

Abstract

The use of high strength steel grades in automotive applications has been widely recorded. This is due largely to vehicle weight reduction programmes as well as increases in vehicle crash safety legislation. This represents the steel industry's response to the challenge that vehicle components manufactured from steel could get replaced with alternative materials, such as aluminium and polymers. Consequently, new high strength steel grades have been developed to offer credible alternatives. Recently, the UK government has released a new specification, BS EN 1317-1-2-3-4: Road Restraint Systems, to which all new safety barrier designs have to comply. However, much of this development and subsequent usage has been targeted at automotive manufacturers. Road safety barrier technology has not evolved in the same way when compared to vehicle technology. Therefore, a study has been undertaken to assess the outcome of using some of these novel high strength steel grades for the manufacture of road safety barrier components. Quasi-static and dynamic tensile testing at different velocities was undertaken. Representative connection coupons were used to understand the energy absorbing properties of a dual phase steel grade when compared to the current CMn steel grade. The present study presents some initial results as to the increased performance that could be gained from utilising new high strength steel grades for the production of road safety barrier systems.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Transportation Safety and Impact Analysis · Engineering and Material Science Research · Nuclear and radioactivity studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Corus CEP, Llanwern Works, Newport NP19 4QZ, UK

Materials Research Centre, School of Engineering, Swansea University, Swansea SA2 8PP, UK

References (20)

Show source-provided references
1. 10.1179/174328405X4103810.1179/174328405X41038 ↗
2. Bodin A., Flemming J., and Jansen E. F. M. ‘Development of A-rolled low silicon and micro-alloyed dual phase steels’, Proc. 42nd MWSP Conf., Toronto, Canada, October 2000, ISS, Vol. 38.
3. 10.1179/174328407X16893710.1179/174328407X168937 ↗
4. 10.1016/j.tws.2008.04.00310.1016/j.tws.2008.04.003 ↗
5. Murugaiyan R., Mohanty R., Pandit A., Saha-Podder A., and Gope N. ‘Effect of composition on microstructure and mechanical properties of dual phase steels – review’; 2005, Jamshedpur, India, Tata Search.
6. AISI Steel Works: http://www.autosteel.org/ (accessed October 2007).
7. British Standards Institute: ‘Hot rolled products of structural steel’, BSEN 10025-1:2004, London, UK, BSI Publications, 2004.
8. British Standards Institute: ‘Vehicle restraint systems’, 1st edn, BS PD 6634-1-2-3-4, London, UK, BSI Publications, 1999.
9. 10.3141/1743-1210.3141/1743-12 ↗
10. Engstrand K., Plaxico C. A., and Ray M. H. ‘Performance of W-beam splices’; 2001, Worcester, MA, Worcester Polytechnic Institute.
11. 10.1016/j.matdes.2007.04.01010.1016/j.matdes.2007.04.010 ↗
12. Vander G. F., Voort: ‘Metallography – principles and practice’, 2nd edn; 2000, New York, McGraw Hill.
13. Dieter G. E. ‘Mechanical metallurgy’, 4th edn; 1988, London, McGraw-Hill.
14. Oberg E., Jones F. D., Horton H. L., and Ryffel H. H. ‘Machinery's handbook’, 25th edn; 1996, New York, Industrial Press Inc.
15. Bickford J. H. ‘An introduction to the design and behaviour of bolted joints’; 1974, New York, Marcel Dekker Inc.
16. Shigley J. E., and Mischke C. R. ‘Mechanical engineering design’, 5th edn; 1989, London, McGraw-Hill.
17. Nethercott D. A. ‘Limit states design of structural steelwork’, 2nd edn; 1996, London, Chapman & Hall.
18. Kulak G. F., Fisher J. W., and Stuik J. H. A. ‘Guide to design criteria for bolted and riveted joints’, 2nd edn; 1987, New York, John Wiley & Sons.
19. 10.1016/S0143-974X(01)00101-810.1016/S0143-974X(01)00101-8 ↗
20. Speich G. R.: in ‘ASM handbook’, Vol. 1, ‘Properties and selection: irons, steels and high performance alloys’, ‘Dual phase steels’; 2002, Seattle, WA, ASM International.