Effect of Mg/nano-Al2O3 interaction time during stirring on microstructure and mechanical properties of Mg–Al2O3 composite
Source abstract
Abstract
In the present study, magnesium based composites containing 1·1 vol. of alumina particulates at nanolength scale were synthesised using disintegrated melt deposition technique. The main focus was to vary interaction time between molten magnesium and nano-Al2O3 particulates during stirring and to study its effects on the microstructure and mechanical properties. With an increase in stirring time, microstructural characterisation of the composite materials revealed reasonably uniform distribution of Al2O3 reinforcement, marginal grain refinement and presence of minimal porosity. Mechanical properties characterisation revealed that an increase in stirring time led to a simultaneous increase in hardness, 0·2 yield strength and ultimate tensile strength while ductility was compromised beyond 7·5 min stirring when compared to pure Mg. The optimal stirring time is observed to be in 5–7·5 min range in order to realise the best combination of strength, hardness, ductility and work of fracture.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering National University of Singapore, 10, Kent Ridge Crescent, 119260, Singapore
References (24)
Show source-provided references
1. 10.1007/978-94-017-0245-4_210.1007/978-94-017-0245-4_2 ↗
2. 10.1179/imr.1994.39.1.110.1179/imr.1994.39.1.1 ↗
3. Fink R:in:‘Die-casting magnesium, magnesium-alloys and technologies’(, Kainer K U, et al.), 23–44; 2003, Berlin, Wiley-VCH Verlag GmbH & Co.10.1002/3527602046.ch2 ↗
4. Evans GB: Proc. Int. Conf. on ‘Applications of magnesium in aerospace, magnesium technology’, 103–109; 1986, London, Institute of Metals.
5. 10.1016/S0921-5093(00)01351-410.1016/S0921-5093(00)01351-4 ↗
6. 10.2320/matertrans.42.115410.2320/matertrans.42.1154 ↗
7. 10.1016/0921-5093(94)90367-010.1016/0921-5093(94)90367-0 ↗
8. 10.1016/S0921-5093(99)00608-510.1016/S0921-5093(99)00608-5 ↗
9. 10.1016/S0025-5408(99)00120-810.1016/S0025-5408(99)00120-8 ↗
10. 10.1023/A:100470632173110.1023/A:1004706321731 ↗
11. 10.1016/j.jallcom.2005.10.00510.1016/j.jallcom.2005.10.005 ↗
12. 10.1016/j.compscitech.2007.03.00610.1016/j.compscitech.2007.03.006 ↗
13. 10.1016/j.msea.2008.09.05010.1016/j.msea.2008.09.050 ↗
14. Ashby MF, Jones DRH: ‘Engineering materials I’, 2nd edn, 82–95; 1996, Oxford/Boston, MA, Butterworth-Heinemann.
15. Morrell R: ‘Handbook of properties of technical and engineering ceramics part 1: an introduction for the engineer and designer’, 82–95; 1985, England, Her Majesty's Stationary Office.
16. Shewmon PG: ‘Transformation in metals’, 69; 1969, New York, McGraw-Hill Book Co.
17. Reed Hill RE, Robert E: ‘Physical metallurgical principles’, 2nd edn, 192–194, 267, 753; 1964, New York, Van Nostrand Company.
18. 10.1179/026708304X398010.1179/026708304X3980 ↗
19. Unverricht R, Peitz V, Riehemann W, Ferkel H: Proc. Conf. on ‘Magnesium alloys and their applications’, Wolsburg, Germany, April 1998, Werkstoff-Informationsgesellschaft mbH, 327–332.
20. 10.1016/S0921-5093(00)01283-110.1016/S0921-5093(00)01283-1 ↗
21. 10.1016/S0921-5093(97)00269-410.1016/S0921-5093(97)00269-4 ↗
22. Murr LE: ‘Interfacial phenomena in metals and alloys’, 202–208, 340–344; 1975, Reading, MA, Addison-Weasley.
23. 10.1016/S0266-3538(03)00215-X10.1016/S0266-3538(03)00215-X ↗
24. 10.1177/002199830707544510.1177/0021998307075445 ↗