journal article·2009-07

Study of welding peak temperatures on microstructures and hardness of heat affected zone in 2024-T3 aluminium alloy

C. S. Chen, J. G. Yang, A. H. Tan

Materials Science and Technology· Volume 25· Issue 7
Publisher page

Abstract

The influence of welding thermal cycle peak temperatures and post-weld heat treatments on the microstructures and mechanical properties of the heat affected zone (HAZ) for 2024-T3 aluminium alloy have been investigated by Gleeble HAZ simulation. Differential scanning calorimetry (DSC) in conjunction with transmission electron microscopy (TEM) is used to characterise the HAZ microstructures. The welded HAZ in the region of peak temperature 414°C has the lowest hardness after natural aged temper, which is primarily due to the precipitation and coarsening of stable S phases. When the peak temperature of welded HAZ is larger than 414°C, the hardness of HAZ increasing with an increasing peak temperature can be seen, which is due to higher peak temperature thermal cycles treatment inducing the dissolution of precipitations in the matrix, and, after the natural aging treatment, Guinier-Preston (GPB) and GPB2 zones precipitating out in the matrix again can be seen. Post-weld T81 artificial aging (PWAA-T81) heat treatment has no effect on improving the HAZ hardness; the HAZ hardness of the 2024-T3 alloy obtained by PWAA-T81 is less than that obtained by natural aging, and its lowest hardness is shifted to the region of peak temperature, which is 452°C, because overaging induces coarse and sparse amounts of stable S phase.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical EngineeringLunghwa Science and Technology University, Guai-Shan, 333, Taiwan

Chun-Shan Institute of Science and TechnologyPO Box no. 90008-15-21, Lung-Tan, Taiwan

Department of Mechanical EngineeringChing-Yun University, Jung-Li, 320, Taiwan;, Email: ahtan@cyu.edu.tw

References (20)

Show source-provided references
1. 10.1016/j.msea.2007.02.10010.1016/j.msea.2007.02.100 ↗
2. 10.1016/S0921-5093(02)00078-310.1016/S0921-5093(02)00078-3 ↗
3. Ringer S. P., Hono K., Sakura T., and Polmear I. J.: Scripta Mater. 1997, 36, 517–521.10.1016/S1359-6462(96)00415-0 ↗
4. Hwang R. Y., and Chou C. P.: Scripta Mater. 1998, 38, 215–221.10.1016/S1359-6462(97)00472-7 ↗
5. Ferragut R., Somoza A., Dupasquier A., and Polmear I. J.: Materials Science Forum, 2002, 396-402, 777–781.10.4028/www.scientific.net/MSF.396-402.777 ↗
6. 10.1016/S1359-6454(99)00422-X10.1016/S1359-6454(99)00422-X ↗
7. 10.1007/BF0267033810.1007/BF02670338 ↗
8. 10.1016/S0921-5093(99)00020-910.1016/S0921-5093(99)00020-9 ↗
9. 10.1016/S0169-4332(02)01375-210.1016/S0169-4332(02)01375-2 ↗
10. 10.1016/j.msea.2004.08.05910.1016/j.msea.2004.08.059 ↗
11. 10.1016/S0921-5093(01)01358-210.1016/S0921-5093(01)01358-2 ↗
12. 10.1179/026708306X8151310.1179/026708306X81513 ↗
13. Iwaki S. · J. Light Metal Weld. Construct · 2007 · 45 · 231
14. 10.1179/174328406X7929810.1179/174328406X79298 ↗
15. 10.1007/BF0326339210.1007/BF03263392 ↗
16. 10.1179/stw.1997.2.6.26110.1179/stw.1997.2.6.261 ↗
17. Lu Z. J., Evans W. J., Parker J. D., and Birley S.: Mat. Sci. Eng., 1996, A220, 1–7.10.1016/S0921-5093(96)10458-5 ↗
18. 10.1088/0965-0393/7/3/30110.1088/0965-0393/7/3/301 ↗
19. DeIASI R. · Metall. Trans · 1977 · 8 · 117710.1007/BF02667403 ↗
20. Jena A. K., Gupta A. K., and Chaturvedi M. C.: Acta Metall. 1989, 37, 885–895.10.1016/0001-6160(89)90015-1 ↗