journal article·2014-07

Fatigue behaviour of Al–25Zn–3Cu alloy

T. Savaşkan, H. O. Tan

Materials Science and Technology· Volume 30· Issue 8
Publisher page

Abstract

In the present study, Al–25Zn–3Cu alloy was prepared by permanent mould casting. Fatigue behaviour of the alloy was investigated using a rotating bending fatigue test machine after determining its microstructural features and mechanical properties. It was observed that as-cast microstructure of the Al–25Zn–3Cu alloy consisted of aluminium rich α dendrites, eutectoid α+ η phases and θ particles. Homogenisation and T6 heat treatment removed the dendritic microstructure of the alloy and produced a large grained microstructure together with zinc rich precipitates. Both heat treatments increased the hardness and strengths of the alloy, but reduced its ductility. The Al–25Zn–3Cu alloy exhibited the lowest and the highest fatigue strengths in the as-cast and T6 heat treated conditions respectively. The fatigue strength of the Al–25Zn–3Cu alloy was found to be much greater than that of the Al–12Si alloy. It was observed that the fatigue behaviour of Al–25Zn–3Cu alloy can be expressed by the Basquin equation.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Mechanical Engineering Department Karadeniz Technical University, Kanuni Campus, Trabzon, 61080 Turkey

Karadeniz Technical University, Trabzon, Turkey

References (27)

Show source-provided references
1. Goodwin FE and Ponikvar AL: ‘Engineering properties of zinc alloys’; 1989, Research Triangle Park, NC, ILZRO.
2. 10.1179/02670830110151039310.1179/026708301101510393 ↗
3. 10.1016/j.matchar.2004.05.00810.1016/j.matchar.2004.05.008 ↗
4. Murphy S · Z. Metallkd · 1980 · 71 · 96
5. 10.1179/mst.1986.2.5.50010.1179/mst.1986.2.5.500 ↗
6. Zhu YH · J. Mater. Sci. Technol. · 1989 · 5 · 113
7. 10.1016/S0142-1123(03)00091-410.1016/S0142-1123(03)00091-4 ↗
8. 10.1007/s11249-008-9299-010.1007/s11249-008-9299-0 ↗
9. 10.1016/j.triboint.2008.04.00810.1016/j.triboint.2008.04.008 ↗
10. 10.1007/s10853-009-3297-y10.1007/s10853-009-3297-y ↗
11. 10.1007/s11249-010-9667-410.1007/s11249-010-9667-4 ↗
12. 10.1016/0043-1648(84)90224-210.1016/0043-1648(84)90224-2 ↗
13. 10.1016/0043-1648(87)90234-110.1016/0043-1648(87)90234-1 ↗
14. 10.1016/j.msea.2005.05.07810.1016/j.msea.2005.05.078 ↗
15. 10.1016/0043-1648(87)90245-610.1016/0043-1648(87)90245-6 ↗
16. 10.2320/matertrans1989.38.70110.2320/matertrans1989.38.701 ↗
17. 10.1016/S1044-5803(99)00057-110.1016/S1044-5803(99)00057-1 ↗
18. 10.1016/j.msea.2008.06.00810.1016/j.msea.2008.06.008 ↗
19. 10.1007/BF0055094710.1007/BF00550947 ↗
20. 10.1016/j.triboint.2007.04.00210.1016/j.triboint.2007.04.002 ↗
21. Ashby MF and Jones DRH: ‘Engineering materials’; 1980, Oxford, Pergamon Press.
22. Dieter GE: ‘Mechanical metallurgy’; 1988, New York, McGraw Hill Co.
23. Avner SH: ‘Introduction to physical metallurgy’; 1974, New York, McGraw Hill Book Co.
24. Callister WDJr and Rethwisch DG: ‘Fundamentals of materials science and engineering’, 3rd edn; 2008, New York, John Wiley & Sons.
25. Khurmi RS and Gupta JK: ‘A textbook of machine design’, 14th edn; 2005, New Delhi, Eurasia Publishing House.
26. Boyer HE: ‘Atlas of fatigue curves’; 1986, Materials Park, OH, ASM.
27. Boyer HE and Gall TL: ‘Metals handbook’; 1985, Metals Park, OH, American Society for Metals.