journal article·1989-11

Microstructures and mechanical properties of milled and continuously cast lead sheet Part 1 Microstructures

S. Whillock, J. A. Charles, G. C. Smith

Materials Science and Technology· Volume 5· Issue 11
Publisher page

Abstract

Milled lead sheet exhibits a recrystallised microstructure, the grain size of which decreases with increasing copper content; copper is present as particles of ~1–5μm in length, formed from the initial needles or plates of the cast billet by spheroidisation, or by particle break-up during rolling. A comparison of materials produced by several manufacturers indicates that the copper distribution and final grain size are dependent on the thermomechanical history of the sheet. Direct method sheet exhibits a cast cellular structure within grains which usually extend through the full thickness of the cast sheet; copper is present as a fine dispersion (particles ~0·5 μm dia.) at cell boundaries. The copper distribution in both materials was stable with prolonged heating (100 h at 200°C), but some grain growth occurred in the milled sheet. It was not possible to obtain a fully dispersed eutectic microstructure at the eutectic composition; primary lead dendrites (or cells) were always present. This is thought to be a result of the difficulty of nucleating a copper particle in the very low copper concentration alloys used in this work.MST/1065
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metallurgy and Material Science · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. L. I. GOFF and R. D. SEMMENS: in Proc. 2nd Int. Lead Conf. ‘Pb '65’, 295; 1965, London, Lead Development Association.
2. L. I. GOFF and G. HEWISH: in Proc. 3rd Int. Lead Conf. ‘Pb '68’, 319; 1968, London, Lead Development Association.10.1016/B978-0-08-015644-6.50028-6 ↗
3. VOCE E. · Technical Memorandum no. 38, British Non-Ferrous Metals Association, London, 1944
4. 10.1016/0026-0800(79)90036-310.1016/0026-0800(79)90036-3 ↗
5. CASANELIA A. J. · Metall. Mater. Technol. · 1977 · 9 · 494
6. GIFKINS R. C. · Metallurgia · 1966 · 74 · 239
7. GrEtuNs R. C. · J. Australasian Inst. Met. · 1976 · 21 · 175
8. 10.1007/BF0287290510.1007/BF02872905 ↗
9. REED-HILL R. E. · AIME · 1964 · 230 · 1019
10. GREENWOOD J. N. · Proc. Australasian Inst. Mining Metall. · 1938 · 109 · 1
11. 10.1016/0026-0800(72)90018-310.1016/0026-0800(72)90018-3 ↗
12. 10.1039/ct892610088810.1039/ct8926100888 ↗
13. BORNMANN K. · Ferrum · 1913 · 11 · 291
14. 10.1021/ja01154a11110.1021/ja01154a111 ↗
15. G. J. DAVIES: ‘Solidification and casting’, 58; 1973, Applied Science.
16. 10.1179/03071697680339165610.1179/030716976803391656 ↗
17. S. ASHOK: PhD thesis, University of Cambridge, 1976.
18. WHILLOCK S. · to be submitted to Mater. Sci. Technol
19. 10.1179/03071697780329218710.1179/030716977803292187 ↗
20. J. W. MARTIN and R. D. DOHERTY: ‘Stability of microstructures in metallic systems’, 186; 1980, Cambridge, Cambridge University Press.
21. 10.1063/1.170882010.1063/1.1708820 ↗