journal article·2003-01

Investigation of blunting line and evaluation of fracture toughness under mixed mode I/III loading in commercially pure titanium

S.V. Kamat, M. Srinivas

Materials Science and Technology· Volume 19· Issue 1
Publisher page

Abstract

The blunting line and fracture toughness in commercially pure titanium under mode I and mixed mode I/III loading was studied. A modified compact tension geometry was used for determining the blunting line as well as mixed mode I/III fracture toughness. The results showed that the constraint factor m in the blunting line equation under mode I loading was 1.84. Also, there was no effect of notch root radius on the slope of the blunting line. The blunting line slope under mixed mode I/III loading was found to be lower than that under mode I loading and agreed with empirical correlations. The fracture toughness under mode I loading was found to be higher for specimens with larger notch root radius. However, notch root independent fracture toughness could be obtained from blunt notch specimen tests using stretch zone width measurements. The fracture toughness was found to decrease with increasing mode III loading.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Fatigue and fracture mechanics · High-Velocity Impact and Material Behavior · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Defence Metallurgical Research Laboratory Kanchanbagh, Hyderabad 500058, India

References (30)

Show source-provided references
1. 10.1016/0013-7944(71)90032-410.1016/0013-7944(71)90032-4 ↗
2. 10.1016/0013-7944(80)90093-410.1016/0013-7944(80)90093-4 ↗
3. UEDA Y. · Eng. Fract. Mech · 1993 · 18 · 1131 — 1158
4. MIGLIN M. T. · Res. Mech · 1984 · 11 · 85
5. 10.1007/BF0115275610.1007/BF01152756 ↗
6. 10.1007/BF0266855510.1007/BF02668555 ↗
7. ROSENFIELD A. R. · Int. J. Fract · 1986 · 32 · R59—R6210.1007/BF00018548 ↗
8. 10.1016/0036-9748(89)90444-410.1016/0036-9748(89)90444-4 ↗
9. 10.1111/j.1151-2916.1987.tb04871.x10.1111/j.1151-2916.1987.tb04871.x ↗
10. MANOHARAN M. · SCr. Metall · 1989 · 23 · 763 — 766
11. 10.1115/1.322649310.1115/1.3226493 ↗
12. 10.1007/BF0264699910.1007/BF02646999 ↗
13. 10.1016/0956-7151(91)90208-I10.1016/0956-7151(91)90208-I ↗
14. 10.1016/0956-716X(91)90489-N10.1016/0956-716X(91)90489-N ↗
15. 10.1007/BF0267557610.1007/BF02675576 ↗
16. 10.1016/0956-7151(93)90144-H10.1016/0956-7151(93)90144-H ↗
17. 10.1007/BF0267077010.1007/BF02670770 ↗
18. 10.1520/JTE11841J10.1520/JTE11841J ↗
19. 10.1520/JTE12460J10.1520/JTE12460J ↗
20. 10.1520/JTE10648J10.1520/JTE10648J ↗
21. CHIPPERFIELEC C. G. · Int. J. Fract · 1976 · 12 · 87310.1007/BF00034625 ↗
22. 10.1016/0013-7944(83)90074-710.1016/0013-7944(83)90074-7 ↗
23. 10.1016/0013-7944(84)90098-510.1016/0013-7944(84)90098-5 ↗
24. PARANJAPE S. A. · Eng. Fract. Mech · 1979 · 11 · 43— 53
25. 10.1016/0013-7944(87)90053-110.1016/0013-7944(87)90053-1 ↗
26. 10.1016/0025-5416(82)90139-210.1016/0025-5416(82)90139-2 ↗
27. 10.1007/BF0001975610.1007/BF00019756 ↗
28. 10.1520/JTE11838J10.1520/JTE11838J ↗
29. 10.1016/S0013-7944(99)00109-510.1016/S0013-7944(99)00109-5 ↗
30. 10.1115/1.280473110.1115/1.2804731 ↗