Effect of auto-tempering on the cold roll-ability of medium-Mn steel
Source abstract
Abstract
Recently, medium-Mn steels have attracted attention for high-strength automotive components. However, because they exhibit martensitic microstructure at room temperature, low cold roll-ability is concerned so that annealing or tempering is often performed before cold rolling. Therefore, we investigated whether cold roll-ability can be improved by adjusting coiling condition in the hot rolling process. For comparison, some specimens were water-quenched or air-cooled after hot rolling. While the water-quenched specimen revealed cracks at ∼30% cold reduction, air-cooled and coiling-simulated specimens at high reductions above ∼68%. This is because the latter had lower and wider ranged hardness values compared to the former due to partial auto-tempering occurring after coiling. The higher coiling temperature caused higher cold roll-ability probably due to the active recovery of austenite. This paper is part of a Thematic Issue on Medium Manganese Steels.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Magnetic Properties and Applications · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Science and Engineering, Yonsei University, Seoul, Republic of Korea
Funding
National Research Foundation of Korea
References (33)
Show source-provided references
1. 10.1016/j.msea.2008.11.01410.1016/j.msea.2008.11.014 ↗
2. 10.1016/j.msea.2006.02.13310.1016/j.msea.2006.02.133 ↗
3. 10.1016/j.scriptamat.2011.12.02610.1016/j.scriptamat.2011.12.026 ↗
4. 10.1007/s11661-011-0942-210.1007/s11661-011-0942-2 ↗
5. 10.1016/j.actamat.2018.01.00910.1016/j.actamat.2018.01.009 ↗
6. 10.1016/j.msea.2016.12.11910.1016/j.msea.2016.12.119 ↗
7. 10.1016/j.scriptamat.2016.07.01310.1016/j.scriptamat.2016.07.013 ↗
8. 10.1080/02670836.2017.131220810.1080/02670836.2017.1312208 ↗
9. 10.1016/j.jmst.2017.06.01710.1016/j.jmst.2017.06.017 ↗
10. 10.1016/j.actamat.2016.09.04810.1016/j.actamat.2016.09.048 ↗
11. 10.1080/09500839.2017.129029310.1080/09500839.2017.1290293 ↗
12. 10.1016/j.actamat.2016.04.03810.1016/j.actamat.2016.04.038 ↗
13. 10.1016/j.msea.2015.11.10310.1016/j.msea.2015.11.103 ↗
14. 10.1016/j.matdes.2015.05.08510.1016/j.matdes.2015.05.085 ↗
15. 10.1179/1743284714Y.000000072210.1179/1743284714Y.0000000722 ↗
16. 10.1016/j.actamat.2013.12.03810.1016/j.actamat.2013.12.038 ↗
17. 10.1016/j.actamat.2014.07.00510.1016/j.actamat.2014.07.005 ↗
18. 10.1007/s11661-012-1402-310.1007/s11661-012-1402-3 ↗
19. 10.2355/isijinternational.53.221810.2355/isijinternational.53.2218 ↗
20. 10.2355/isijinternational.53.187110.2355/isijinternational.53.1871 ↗
21. 10.1016/j.msea.2011.11.00910.1016/j.msea.2011.11.009 ↗
22. 10.1016/j.scriptamat.2010.12.01210.1016/j.scriptamat.2010.12.012 ↗
23. 10.1007/s11661-011-0687-y10.1007/s11661-011-0687-y ↗
24. 10.1016/j.msea.2011.05.03910.1016/j.msea.2011.05.039 ↗
25. 10.1016/j.scriptamat.2010.06.02310.1016/j.scriptamat.2010.06.023 ↗
26. 10.1007/BF0264766510.1007/BF02647665 ↗
27. 10.1016/j.scriptamat.2017.01.02210.1016/j.scriptamat.2017.01.022 ↗
28. 10.1016/j.matdes.2016.02.05810.1016/j.matdes.2016.02.058 ↗
29. 10.1016/j.jallcom.2012.04.10810.1016/j.jallcom.2012.04.108 ↗
30. 10.1016/j.msea.2016.04.03810.1016/j.msea.2016.04.038 ↗
31. 10.1016/j.msea.2012.09.07810.1016/j.msea.2012.09.078 ↗
32. 10.1016/j.actamat.2010.09.04210.1016/j.actamat.2010.09.042 ↗
33. 10.1016/j.actamat.2014.12.02110.1016/j.actamat.2014.12.021 ↗