journal article·2007-01

Plain fatigue and fretting fatigue behaviour of AISI 304 austenitic stainless steel

S. Ganesh Sundara Raman, M. Jayaprakash

Materials Science and Technology· Volume 23· Issue 1
Publisher page

Abstract

The present work deals with the influence of deformation induced martensite formation and grain size on plain fatigue (PF) (without fretting) and fretting fatigue (FF) behaviour of AISI 304 austenitic stainless steel at room temperature. Two grain sizes, namely 43 and 277 μm, were developed via suitable solution annealing treatments. The martensitic transformation was studied using a ferrite scope, X-ray diffractometry, optical and transmission electron microscopy. More martensite formed in coarse grained (CG) material and at higher cyclic stress levels. Owing to the additional influence of contact stress, more martensite formed in the fretting scar region of FF tested samples compared with that in the PF tested specimens. In PF tests conventional behaviour was observed at higher cyclic stress levels, i.e. fine grained material showed superior fatigue lives. But at lower cyclic stress levels CG material exhibited superior fatigue lives. This was explained in terms of amount and time of martensite formation and whether crack initiation or propagation controlled the fatigue life at a given stress level. Fretting fatigue test results indicated a tendency for cross-over in the stress life plots corresponding to two grain sizes.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical stress and fatigue analysis · Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Marshall P.: Austenitic stainless steels — microstructure and mechanical properties’, 1st edn, 31; 1984, London, Elsevier Applied Science Publishers.
2. Maxwell P. C., Goldberg A., and Shyne J. C.: Metall Trans. 1974, 5, 1319–1324.10.1007/BF02646614 ↗
3. 10.1016/0001-6160(78)90211-010.1016/0001-6160(78)90211-0 ↗
4. Pineau A. G., and Pelloux R. M.: Metall Trans. 1974, 5, 1103–1112.10.1007/BF02644322 ↗
5. 10.1007/BF0264294510.1007/BF02642945 ↗
6. Bayerlein M., Christ H. J., and Mughrabi H.: Mater. Scl. Eng. A, 1989, A114, L11—L16.10.1016/0921-5093(89)90871-X ↗
7. 10.1007/BF0264283810.1007/BF02642838 ↗
8. K. Bhanu Sankara Rao: ‘Effect of metallurgical variables on the low cycle fatigue behaviour of AISI 304 stainless steel’, PhD thesis, Madras University, Chennai, India, 1989.
9. Ganesh Sundara S. · Mater. Scl. Technol · 1994 · 10 · 61410.1179/mst.1994.10.7.614 ↗
10. 10.1016/0036-9748(71)90059-710.1016/0036-9748(71)90059-7 ↗
11. Thompson A. W., and Backofen W. A.: Acta Metall. 1971, 19, 597–606.10.1016/0001-6160(71)90012-5 ↗
12. 10.1179/imr.1992.37.1.7710.1179/imr.1992.37.1.77 ↗
13. Dobromirski J. M.: in ‘Standardization of fretting fatigue tests and equipment’, (ed.Attia H. M., and Waterhouse R. B.), 60-66; 1992, Philadelphia, PA, American Society of Testing and Materials.10.1520/STP25816S ↗
14. Ramakrishna Naidu N. K., and Ganesh S., Raman Sundara: Int. J. Fatigue, 2005, 27,323–331.10.1016/j.ijfatigue.2004.07.007 ↗
15. 10.1046/j.1460-2695.1999.00145.x10.1046/j.1460-2695.1999.00145.x ↗
16. Ochi Y., Kido Y., Akiyama T., and Matsumura T.: in ‘Fretting fatigue: advances in basic understanding and applications’, (ed.Mutoh Y. et al), 220-232; 2003, West Conshohocken, PA, American Society of Testing and Materials.10.1520/STP10762S ↗
17. Puglia A., Pratesi F., and Zonfrillo G.: in ‘Fretting fatigue’, (ed.Waterhouse R. B., and Lindley T. C.), 219-238; 1994, London, Mechanical Engineering Publications.
18. Ganesh Sundara S. · J. Mater. Set Lett · 1994 · 13 · 38910.1007/BF00420808 ↗
19. Tjong S. C., and Ho N. J.: Mater. Set Eng. A, 1988, A102,125–130.10.1016/0025-5416(88)90540-X ↗
20. Rayaprolu D. B., and Cook R.: in ‘Standardization of fretting fatigue test methods and equipment’, (ed.Attia M. H., and Waterhouse R. B.), 129-152; 1992, Philadelphia, PA, American Society for Testing and Materials.10.1520/STP25826S ↗
21. Lagneborg R.: Acta Metall. 1964, 12, 823–843.10.1016/0001-6160(64)90176-2 ↗
22. 10.1007/BF0264200310.1007/BF02642003 ↗
23. Liang F.L., and Laird C.: Mater. Set Eng. A, 1989, A117,95–102.10.1016/0921-5093(89)90090-7 ↗