Microstructure and wear characteristics of spray formed and hot extruded Al–Si alloys
Source abstract
Abstract
The microstructural and wear properties of spray formed Al–6.5Si, Al–18Si and Al–18Si–5Fe–1.5Cu (wt-%) alloys have been investigated. The microstructure of the Al–6.5Si alloy exhibits the equiaxed grain morphology of the primary α-Al phase with eutectic Si at the grain boundaries. The size of the primary Si particulates in the Al–18Si alloy varied from 3 to 8 μm embedded in the eutectic matrix. Complex intermetallic phases such as β-Al5 SiFe and δAl4 Si2 Fe are observed to co-exist with primary Si in the spray formed Al–18Si–5Fe–1.5Cu alloy system. The periphery of the preforms invariably showed pre-solidified particles with a large amount of interstitial pores. An extrusion ratio of 6 : 1 for these alloys led to drastic porosity reduction and extensive breaking of second phase particles. These microstructural features showed distinct variation in the wear behaviour and the coefficient of friction of the alloys. The Al–18Si–5Fe–1.5Cu alloy shows better wear resistance compared with the other two alloys, particularly at higher loads. The coefficient of friction shows a dependence upon the applied load. However, this becomes steady at higher loads. The wear behaviour of these alloys is discussed in light of the morphology of debris particles as well as that of the worn surfaces.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. TENEKEDJIEV N. · Cast Met · 1990 · 3 · 9610.1080/09534962.1990.11819026 ↗
2. 10.1016/0301-679X(94)90042-610.1016/0301-679X(94)90042-6 ↗
3. 10.1007/s11661-998-0315-710.1007/s11661-998-0315-7 ↗
4. JORSTAD J. L. · AFS Trans · 1971 · 79 · 85
5. R. ELLIOT: 'Eutectic solidification processing: crystalline and glassy alloys'; 1983, London, Butterworth.10.1016/B978-0-408-10714-3.50007-1 ↗
6. E. J. LAVERNIA and Y. WU: 'Spray atomisation and deposition'; 1996, Chichester, Wiley.
7. 10.1016/0079-6425(95)00004-610.1016/0079-6425(95)00004-6 ↗
8. SRIVASTAVA V. C. · PIM Sci. Technol. Briefs · 2001 · 3 · 5
9. 10.2320/matertrans1989.39.121410.2320/matertrans1989.39.1214 ↗
10. IAVERNIA E. J. · Int. J. Rapid Solid · 1989 · 5 · 47
11. 10.1016/S1359-6462(99)00147-510.1016/S1359-6462(99)00147-5 ↗
12. 10.1023/A:100679821154810.1023/A:1006798211548 ↗
13. KANTH V. K. · Ser. Metall · 1990 · 24 · 267
14. 10.1007/BF0239693010.1007/BF02396930 ↗
15. 10.1016/0043-1648(87)90102-510.1016/0043-1648(87)90102-5 ↗
16. 10.1080/0569819860898166710.1080/05698198608981667 ↗
17. 10.1016/0025-5416(87)90412-510.1016/0025-5416(87)90412-5 ↗
18. J. B. ANDREWS, M. V. SENEVIRATNE, K. P. ZEIR and T. R. JETT: in 'Wear of Metals', (ed. K. C. Ludema), p. 180; 1985, New York, Americal Society of Mechanical Engineers.
19. 10.1016/0043-1648(79)90044-910.1016/0043-1648(79)90044-9 ↗
20. SRIVASTAVA V. C. · Trans. Indian Inst. Met · 1999 · 51 · 29
21. 10.1016/S0167-577X(02)00616-X10.1016/S0167-577X(02)00616-X ↗
22. W. A. GLAESER: in 'Applied metallography', (ed. G. F. Vandervoort), p. 261; 1986, New York, Van Nostrand Reinhold.10.1007/978-1-4684-9084-8_16 ↗
23. 10.1016/0043-1648(87)90133-510.1016/0043-1648(87)90133-5 ↗