journal article·1997-01

Microstructural changes induced by dry sliding wear of a A357/SiC metal matrix composite

A. J. Leonard, C. Perrin, W. M. Rainforth

Materials Science and Technology· Volume 13· Issue 1
Publisher page

Abstract

The sliding wear behaviour of a commercial (Duralcan) metal matrix composite containing 30 vol.-%SiC particles, and that of the unreinforced A357 matrix alloy were investigated in the load range 6-74 N and a sliding speed of 1 m s−1 against a grey castiron counterface. At the lowest load (6 N) the wear coefficient of the composite (3.1 × 10−6 mm3 N−1 m−1) was lower than that of the monolithic alloy (169.6 × 10−6 mm3 N−1 m−1 ). Between 18 and 40 N the wear performance of the two materials was verysimilar but at the highest load (74 N) the wear coefficient of the composite (176.8 × 10−6 mm3 N−1 m−1) was much higher thanthat of the monolithic alloy (89 × 10−6 mm3 N−1 m−1). The maximum depth offriction induced deformation wasfound to beabout three times higher for the composite than the monolithic alloy at a load of 74 N. Detailed TEM was performed on the surface of the composite. The SiC was found to be fragmented. Extensive formation of a alumina was observed, and the presenceof iron oxides indicated transfer from the counterface. Widespread cracking was found at the SiC/matrix and lI. alumina/matrixinterfaces. The matrix had developed a fine subgrain structure with little evidence of the Mg2Si which was present in the startingstructure.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. 10.1007/BF0059148310.1007/BF00591483 ↗
2. 10.1016/0043-1648(82)90055-210.1016/0043-1648(82)90055-2 ↗
3. 10.1179/mst.1989.5.1.7110.1179/mst.1989.5.1.71 ↗
4. HUTCHINGS I. M. · Inst. Phys. Conf. Ser., · 1990 · 111 · 91
5. 10.1016/0043-1648(92)90111-K10.1016/0043-1648(92)90111-K ↗
6. 10.1016/0043-1648(92)90068-J10.1016/0043-1648(92)90068-J ↗
7. 10.1016/0043-1648(91)90290-B10.1016/0043-1648(91)90290-B ↗
8. 10.1016/0043-1648(92)90305-R10.1016/0043-1648(92)90305-R ↗
9. 10.1016/0301-679X(94)90024-810.1016/0301-679X(94)90024-8 ↗
10. 10.1007/BF0045656310.1007/BF00456563 ↗
11. 10.1016/0956-716X(90)90140-C10.1016/0956-716X(90)90140-C ↗
12. 10.1016/0043-1648(92)90071-F10.1016/0043-1648(92)90071-F ↗
13. 10.1016/0043-1648(92)90112-L10.1016/0043-1648(92)90112-L ↗
14. 10.1080/1040200920898214610.1080/10402009208982146 ↗
15. 'Metals handbook', 9th edn, Vol. 10, ‘Materials characterisa-tion’, 31; 1986, Metals Park, OH, American Society for Metals.
16. PERIUN C. · PhD thesis · 1994 · University of S
17. 10.1007/BF0072149510.1007/BF00721495 ↗
18. 10.1007/BF0266979610.1007/BF02669796 ↗
19. 10.1007/BF0264703310.1007/BF02647033 ↗
20. 10.1080/0141861920820158010.1080/01418619208201580 ↗
21. 10.1016/0025-5416(86)90279-X10.1016/0025-5416(86)90279-X ↗
22. 10.1016/1359-6462(95)00598-610.1016/1359-6462(95)00598-6 ↗