journal article·2023-12Open access

Dissolution controlled grain growth in Nickel Alloy UDIMET 720Li

Manish Purushottam Meshram, Daniel Fabijanic, Rajkumar P. Singh, Matthew R. Barnett

Materials Science and Technology· Volume 39· Issue 17

Abstract

The present paper examines the mechanisms for simultaneous manipulation of grain size and γ′ dissolution leading to the microstructure that balance creep and fatigue properties in UDIMET 720Li. For sub (near) solvus heat treatments, grain growth and γ′ dissolution occur simultaneously. Grain size following heat treatment is determined largely by the primary γ′ particle dispersion, via Zener-Smith pinning. Remarkably, grain growth occurs only as a result of precipitate dissolution. The resulting grain size is dictated by a combination of initial particle dispersion in the as-received material and heat treatment temperature. It is likely to hold so long as the initial grain size is close to the Zener-Smith limit and where the kinetics of grain growth and dissolution share similar rates.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Institute for Frontier Materials, Deakin University, Waurn Ponds, Australia

Kalyani Centre for Technology and Innovation, Bharat Forge, Pune, India

References (18)

Show source-provided references
1. 10.1017/CBO978051154128510.1017/CBO9780511541285 ↗
2. Mitchell RJ · Proc Int Symp Superalloys · 2008 · 347
3. 10.1016/j.ijplas.2013.08.00910.1016/j.ijplas.2013.08.009 ↗
4. 10.1016/B978-0-444-53770-6.00022-810.1016/B978-0-444-53770-6.00022-8 ↗
5. 10.2320/matertrans.M201528310.2320/matertrans.M2015283 ↗
6. Humphreys FJ · 2004
7. Smith CS. · Trans Metall Soc AIME · 1948 · 175 · 15
8. 10.1016/j.msea.2007.09.05510.1016/j.msea.2007.09.055 ↗
9. 10.1016/j.actamat.2013.02.02810.1016/j.actamat.2013.02.028 ↗
10. 10.22226/2410-3535-2021-3-261-26610.22226/2410-3535-2021-3-261-266 ↗
11. Vaunois J-R, Cormier J, Villechaise P, Influence of both γ′ distribution and grain size on the tensile properties of UDIMET 720Li at room temperature. Superalloy 718 Deriv. Hoboken (NJ): John Wiley; 2012. 198–213. Available from: http://doi.wiley.com/10.10029781118495223.ch14.10.1002/9781118495223.ch14 ↗
12. 10.1007/s11661-005-0284-z10.1007/s11661-005-0284-z ↗
13. Maurer GE. Development of UDIMET 720 for high strength disk application. Superalloys 1984. Pennsylvania: Metallurgical Society of AIME; 1984. 573–582.10.7449/1984/Superalloys_1984_573_580 ↗
14. 10.1016/j.jallcom.2015.09.00110.1016/j.jallcom.2015.09.001 ↗
15. Hermann W · Proc of 10th Int Symp Superalloys · 2004 · 51710.7449/2004/Superalloys_2004_517_522 ↗
16. 10.3390/met1112192110.3390/met11121921 ↗
17. 10.1016/0502-8205(52)90009-910.1016/0502-8205(52)90009-9 ↗
18. 10.2355/isijinternational.38.91310.2355/isijinternational.38.913 ↗