Effect of heat treatment on small scale fragmentation of aluminium alloy
Source abstract
Abstract
Small scale explosions, using a detonator, of 7075 aluminium alloy cylinders, 15–100 mm outside diameter, were carried out to investigate the effects of heat treatment on fragmentation. This was the finest for the strongest as received alloy and coarsest for the softest overaged alloy. This effect was similar to that seen in investigations of the fragmentation of steel. Cylinders of 50 and 100 mm in diameter did not fragment but plastically deformed with maximum deformation at the cylinder bottom. Fragmentation of 33 and 42 mm diameter cylinders produced long fragments typical of the break-up of thick walled cylinders. At smaller diameters, break-up gave fragments of several shapes, finer fragments being largely associated with the smallest diameter cylinders and the highest strength alloys. Results followed those seen in large scale studies of cylinder break-up and suggest the possibility of using small scale fragmentation experiments in the investigation of the effects of composition, heat treatment and processing on natural fragmentation.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Energetic Materials and Combustion · Ion-surface interactions and analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Applied Science, Security and Resilience, Cranfield University, Defence Academy of the United Kingdom, Shrivenham, Swindon SN6 8LA, UK
References (25)
Show source-provided references
1. Gurney R. ‘The initial velocities of fragments in bombs, shells and grenades’, Report 405, Ballistic Research Laboratory, Aberdeen, MD, USA, 1943 (cited in M. A. Meyers: ‘Dynamic behavior of materials’, 234–242; 1994, New York, John Wiley & Sons).10.21236/ADA289704 ↗
2. 10.1179/174328406X9118610.1179/174328406X91186 ↗
3. 10.1179/174328406X8410210.1179/174328406X84102 ↗
4. 10.1179/174328406X9106910.1179/174328406X91069 ↗
5. Mott N. F. · Proc. R. Soc. Lond. A · 1947 · 189 · 30010.1098/rspa.1947.0042 ↗
6. 10.1063/1.32993410.1063/1.329934 ↗
7. 10.1016/j.ijimpeng.2003.09.02610.1016/j.ijimpeng.2003.09.026 ↗
8. 10.1063/1.33234610.1063/1.332346 ↗
9. 10.1016/S0734-743X(97)87502-110.1016/S0734-743X(97)87502-1 ↗
10. 10.1063/1.33613910.1063/1.336139 ↗
11. 10.1063/1.170222410.1063/1.1702224 ↗
12. Rinehart J. S., and Pearson J. ‘Behavior of materials under impulsive loads’, 136–137; 1954, New York, Dover Press.
13. Lidstone D. P. ‘Cartridge case deformation test’, RARDE Memorandum 15/69, RARDE, Surrey, UK, 1969.
14. 10.1080/0737065980823023610.1080/07370659808230236 ↗
15. 10.1520/JFS15100J10.1520/JFS15100J ↗
16. Walsh B. E. ‘Comparison of natural fragmentation scaling behavior of HF-1 and AISI 1045 steel cylinders using normalized Payman parameters’, Report MRL-R-941, DSTO Materials Research Laboratories, Ascot Vale, Vic., Australia, 1984.
17. 10.1002/978352761704310.1002/9783527617043 ↗
18. Taylor G. I. ‘The scientific papers of Sir Geoffrey Ingram Taylor’, Vol. III, 277–286; 1963, Cambridge, Cambridge University Press.
19. 10.1002/prep.1994019010310.1002/prep.19940190103 ↗
20. Catanach R., Hill L., Harry H., Aragon E., and Murk D. ‘Cylinder test specification’, Report LA-13643-MS, Los Alamos National Laboratory, Los Alamos, NM, USA, 1999.
21. 10.1002/978047017227810.1002/9780470172278 ↗
22. 10.1007/BF0003508710.1007/BF00035087 ↗
23. Available at: http://www.matweb.com (accessed 29 July 2009).
24. Develay R.: Metals and Materials, 1972, 6, 404-410 (cited in I J Polmear: ’Light alloys‚, 4th edition, 135; 2006, Oxford, Butterworth-Heinemann
25. Clark D. S. · Trans. ASM · 1950 · 42 · 45