journal article·2020-11

Characterisation of nickel–aluminium bronze powders produced by the planar flow casting method

Sultan Öztürk, Sefa Emre Sünbül, Abdurrahim Metoğlu, Suat Önal, Kürşat İçin

Materials Science and Technology· Volume 36· Issue 16
Publisher page

Abstract

CuAl10Ni5Fe4 alloy powders were successfully produced using the planar flow casting method, known as the continuous ribbon production process. Cooling the textured wheel to -5 ºC resulted in a much finer microstructure in comparison to uncooled wheel powders. The microstructure of the powders, in case of the cooled wheel, consisted of β′ martensite, which resides inside the colonies, and proeutectoid α phase at colony boundaries. The martensite start and finish temperatures for uncooled wheel powders were obtained as 221 ºC, and 174 ºC, respectively. The Ms and Mf temperatures for cooled wheel powders were measured as 207 ºC, and 135 ºC, respectively. It is observed that the magnetic properties of the produced powders change with the amount of β′ martensite.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metallurgy and Material Science · Nanoporous metals and alloys · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Metallurgy and Materials Engineering, Karadeniz Technical University, Trabzon, Turkey

Department of Metallurgy and Materials Engineering, Gaziantep University, Gaziantep, Turkey

Kartek Metalurji, Has Industry Area, İstanbul, Turkey

Osmaniye Vocational School, Osmaniye Korkut Ata Üniversity, Osmaniye, Turkey

Funding

Scientific and Technological Research Council of Turkey · TUBITAK

References (37)

Show source-provided references
1. 10.1007/BF0264287010.1007/BF02642870 ↗
2. 10.4028/www.scientific.net/KEM.778.6110.4028/www.scientific.net/KEM.778.61 ↗
3. 10.1016/j.surfcoat.2017.07.01910.1016/j.surfcoat.2017.07.019 ↗
4. 10.3390/ma1208126710.3390/ma12081267 ↗
5. 10.3390/met503169510.3390/met5031695 ↗
6. 10.1016/j.corsci.2018.08.05810.1016/j.corsci.2018.08.058 ↗
7. Slama P · Mater Technol · 2014 · 48 · 599
8. 10.1016/0043-1648(95)06773-610.1016/0043-1648(95)06773-6 ↗
9. Nová I · Manuf Technol · 2017 · 17 · 797
10. 10.30544/42310.30544/423 ↗
11. 10.1007/s11665-015-1838-x10.1007/s11665-015-1838-x ↗
12. 10.1016/j.matchar.2018.07.00210.1016/j.matchar.2018.07.002 ↗
13. 10.1179/03071698080328657710.1179/030716980803286577 ↗
14. 10.1016/j.msea.2009.06.01310.1016/j.msea.2009.06.013 ↗
15. 10.2478/afe-2013-006310.2478/afe-2013-0063 ↗
16. 10.1016/j.corsci.2005.05.05310.1016/j.corsci.2005.05.053 ↗
17. Koçak TÜ, Özeren T, Arısoy CF. Effect of Ti addition on microstructure, mechanical properties and wear behavior of a nickel aluminum bronze. 19th International Metallurgy & Materials Congress, İstanbul, 2018. p. 136–139.
18. 10.1179/imr.1982.27.1.7710.1179/imr.1982.27.1.77 ↗
19. 10.30772/qjes.v11i3.56510.30772/qjes.v11i3.565 ↗
20. 10.1016/j.procir.2016.01.07910.1016/j.procir.2016.01.079 ↗
21. Öztürk S · J Non Cryst Solids · 2020 · 527 · 11974510.1016/j.jnoncrysol.2019.119745 ↗
22. 10.1016/S0924-0136(03)00466-710.1016/S0924-0136(03)00466-7 ↗
23. 10.1016/0921-5093(92)90117-J10.1016/0921-5093(92)90117-J ↗
24. Öztürk S · J Non Cryst Solids · 2019 · 522 · 11959210.1016/j.jnoncrysol.2019.119592 ↗
25. 10.1007/s10948-018-4561-710.1007/s10948-018-4561-7 ↗
26. 10.1007/BF0335439510.1007/BF03354395 ↗
27. 10.1016/j.stam.2007.03.00110.1016/j.stam.2007.03.001 ↗
28. 10.1179/imr.1992.37.1.110.1179/imr.1992.37.1.1 ↗
29. 10.1007/BF0111603510.1007/BF01116035 ↗
30. 10.1007/s11665-015-1386-410.1007/s11665-015-1386-4 ↗
31. 10.1016/S1003-6326(19)64947-210.1016/S1003-6326(19)64947-2 ↗
32. 10.1016/j.vacuum.2020.10919510.1016/j.vacuum.2020.109195 ↗
33. Cuevas AM. · 2002
34. 10.1016/j.jnucmat.2007.03.26210.1016/j.jnucmat.2007.03.262 ↗
35. 10.1007/BF0054872810.1007/BF00548728 ↗
36. Howell PR. · 2000
37. 10.1007/s11665-013-0759-910.1007/s11665-013-0759-9 ↗