journal article·2011-12

Extrusion of EN AW-2014 alloy in semisolid state

Y Birol, E A Guven, L J Capan

Materials Science and Technology· Volume 27· Issue 12
Publisher page

Abstract

The potential of forming EN AW-2014 alloy in semisolid state was investigated. The EN AW-2014 slugs were partially melted at 610°C, to a liquid fraction of ∼15, before they were extruded into a solid bar with a diameter of 16 mm. The ram speed used in this process was much lower than that employed in thixoforging of the same alloy to maximise heat removal from the slug and to fully solidify the liquid fraction by the time the extruded bar exits the die. The high solid fraction employed was also of help in this regard. Forming during extrusion under these conditions took place largely via rotation of the α-Al globules over one another, producing a remarkable microstructure of predominantly uniform globular α-Al grains. The forming load was at least an order of magnitude smaller with respect to that measured during hot extrusion of the same alloy, underlining the benefits of extruding the hard to form 2XXX alloys in semisolid state. Having been largely drained of its liquid, the final part of the preheated slug, however, failed to enjoy extrusion under such favourable conditions. The large extrusion deformation and temperatures well above the liquidus point have led to dynamic recrystallisation, which is responsible for the equiaxed, instead of fibrous, grain structure in this region.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Materials Institute, Marmara Research Centre, TUBITAK, Gebze, Kocaeli, Turkey

Department of Mechanical Engineering, Faculty of Engineering, Kocaeli University, Kocaeli, Turkey

References (25)

Show source-provided references
1. Polmear IJ: ‘Light alloys – metallurgy of the light metals’; 1996, London, Halsted Press.
2. Hatch JE: ‘Aluminium properties and physical metallurgy’; 1984, Materials Park, OH, ASM.
3. 10.4028/www.scientific.net/MSF.396-402.39310.4028/www.scientific.net/MSF.396-402.393 ↗
4. Kiuchi K, Sugiyama S: Proc. 3rd Int. Conf. on ‘Semi-solid processing of alloys and composites’, (ed. , Kiuchi M), 245; Tokyo, Tokyo Institute of Industrial Science.
5. 10.1007/BF0266109010.1007/BF02661090 ↗
6. 10.1179/imr.1994.39.5.17310.1179/imr.1994.39.5.173 ↗
7. 10.1179/09506600122500107610.1179/095066001225001076 ↗
8. Kenney MP, Courtois JA, Evans RD, Farrior GM, Kyonka CP, Koch AA, Young KP: in ‘Metals handbook’, 9th edn, Vol. 15, 327; 1988, Materials Park, OH, ASM.
9. 10.1016/j.pmatsci.2004.04.00310.1016/j.pmatsci.2004.04.003 ↗
10. 10.1016/j.jallcom.2008.05.07410.1016/j.jallcom.2008.05.074 ↗
11. 10.1016/j.jallcom.2008.02.09310.1016/j.jallcom.2008.02.093 ↗
12. 10.1016/j.jmatprotec.2007.12.07110.1016/j.jmatprotec.2007.12.071 ↗
13. 10.1016/j.jallcom.2007.01.05310.1016/j.jallcom.2007.01.053 ↗
14. 10.1016/j.jmatprotec.2006.11.17710.1016/j.jmatprotec.2006.11.177 ↗
15. 10.1016/j.matdes.2010.03.03210.1016/j.matdes.2010.03.032 ↗
16. 10.1016/S1003-6326(10)60621-810.1016/S1003-6326(10)60621-8 ↗
17. 10.1016/j.jmatprotec.2004.04.31410.1016/j.jmatprotec.2004.04.314 ↗
18. 10.1016/j.jmatprotec.2003.11.00710.1016/j.jmatprotec.2003.11.007 ↗
19. 10.1016/0921-5093(95)09861-510.1016/0921-5093(95)09861-5 ↗
20. 10.1016/S0921-5093(00)00908-410.1016/S0921-5093(00)00908-4 ↗
21. 10.4028/www.scientific.net/MSF.396-402.13110.4028/www.scientific.net/MSF.396-402.131 ↗
22. Birol Y
23. 10.1016/j.msea.2008.01.05710.1016/j.msea.2008.01.057 ↗
24. 10.1016/B978-0-408-70932-3.50213-810.1016/B978-0-408-70932-3.50213-8 ↗
25. 10.1007/s11661-000-0141-z10.1007/s11661-000-0141-z ↗