Fabrication of TiC–Fe cermet coating by plasma spraying of Fe–Ti–C powder using sucrose as carbon source
Source abstract
Abstract
A mixture of ferrotitanium and sucrose was heated to carbonise the sucrose, so the ferrotitanium particles were bound by the carbon obtained from the pyrolysis of sucrose. Then a Fe–Ti–C composite powder was made for reactive thermal spraying, which could avoid separation of Ti and C during spraying. The carbon is a reactive constituent as well as the binder in the composite powder. While this powder was used to deposit cermet coating by plasma spraying, a mass of TiC particles were in situ synthesised and uniformly distributed within metallic matrix. Average microhardness and surface hardness of the TiC–Fe coating are about 1672·5 HV0·2 and 91·4 HR(15 N) respectively. Adhesive strength value of the coating reaches 61·86 MPa. Finally, the cermet coating has good wear resistance performance.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Materials Advanced Joining Technology LaboratorySchool of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
References (31)
Show source-provided references
1. Zhou J. · Surf Coat. Technot · 2001 · 30 · 23
2. 10.1016/0257-8972(94)02266-S10.1016/0257-8972(94)02266-S ↗
3. Basu S. N., and Sarin V. K.: Mater. Set Eng. A, 1996, A209,206–212.10.1016/0921-5093(95)10145-4 ↗
4. Exner H. E. · Int. Met. Rev · 1979 · 4 · 149
5. Liu H. Y. · Chin. J. Nonferr. Met · 2004 · 14 · 1389
6. 10.1016/0257-8972(91)90162-P10.1016/0257-8972(91)90162-P ↗
7. 10.1016/S0043-1648(97)00212-310.1016/S0043-1648(97)00212-3 ↗
8. Eigen N., Klassen T., Aust E., Bormann R., and Garner F.: Mater. Set Eng. A, 2003, A356,114–121.10.1016/S0921-5093(03)00110-2 ↗
9. Contreras A., Bedolla E., and Perez R.: Acta Mater. 2004, 52, 985–994.10.1016/j.actamat.2003.10.034 ↗
10. 10.1016/0272-8842(95)00141-710.1016/0272-8842(95)00141-7 ↗
11. 10.1016/S0272-8842(02)00196-710.1016/S0272-8842(02)00196-7 ↗
12. Liu C. S. · Trans. Nonferr. Met. Soc. Chn · 2000 · 10 · 405
13. Liu H. Y. · J. Mater. Set Technot · 2006 · 14 · 229
14. 10.1016/S0925-8388(99)00061-410.1016/S0925-8388(99)00061-4 ↗
15. 10.1016/S0263-4368(97)87505-110.1016/S0263-4368(97)87505-1 ↗
16. Benedicte H., Jean-Pierre B., Pierre F., Alain G., and Jean-Claude L. ‘TiC based coatings prepared by combining SHS and plasma spraying, Proc. Thermal Spray 2004: ‘Advances in technology and application’, Osaka, Japan, May 2004, ASM International,666–669.10.31399/asm.cp.itsc2004p0666 ↗
17. 10.1016/S0043-1648(00)00455-510.1016/S0043-1648(00)00455-5 ↗
18. Zhang L. M., Sun D. B., Yu H. Y., and Li H. Q.: Mater. ScL Eng. A, 2007, A457,319–324.10.1016/j.msea.2006.12.047 ↗
19. 10.1016/j.jallcom.2005.09.08410.1016/j.jallcom.2005.09.084 ↗
20. Hui X. D., Yang Y. S., Wang Z. F., Yuan G. Q., and Chen X. C.: Mater. Set Eng. A, 2000, A282,187–192.10.1016/S0921-5093(99)00751-0 ↗
21. 10.1016/S0167-577X(03)00020-X10.1016/S0167-577X(03)00020-X ↗
22. Huang J. H., Liu C. S., and Dang Q. K.: Powder Metall. 2002, 20, 219–222.
23. 10.1016/S0257-8972(99)00045-610.1016/S0257-8972(99)00045-6 ↗
24. 10.1361/1059963052274710.1361/10599630522747 ↗
25. 10.1016/0008-6223(88)90155-810.1016/0008-6223(88)90155-8 ↗
26. Liu H. Y. · Acta Mater. Compos. Sin · 2005 · 22 · 80
27. Staia M. H., Ramos E., Carrasquero A., Roman A., Lesage J., Chicot D., and Mesmacque G.: Thin Solid Films, 2000, 377-378,657–664.10.1016/S0040-6090(00)01447-4 ↗
28. 10.1016/j.molcata.2005.04.02810.1016/j.molcata.2005.04.028 ↗
29. 10.1016/S0165-2370(02)00105-510.1016/S0165-2370(02)00105-5 ↗
30. 10.1016/j.surfcoat.2005.06.01610.1016/j.surfcoat.2005.06.016 ↗
31. 10.1016/j.ceramint.2006.01.02010.1016/j.ceramint.2006.01.020 ↗