journal article·2004-10

Formation of aluminide coatings on low alloy steels at 650°C by pack cementation process

Z.D. Xiang, P.K. Datta

Materials Science and Technology· Volume 20· Issue 10
Publisher page

Abstract

The pack aluminising process is normally conducted on alloy steels at temperatures higher than 900°C at which mechanical properties of steels would degrade. This study aims to investigate the feasibility of pack aluminising a commercial 9Cr – 1Mo alloy steel at 650°C in an attempt to increase its high temperature oxidation and corrosion resistance without adversely affecting its mechanical properties and consequently to increase its long-term structural operating temperatures to up to 700°C. It was demonstrated that this could be achieved using packs containing AlCl 3 as an activator and elemental Al as a depositing source. The coatings formed under these conditions consisted of an outer Fe 14 Al 86 layer and an inner FeAl 3 layer with an abrupt interface between the coating and substrate, suggesting that the coating is formed via a mechanism of the inward Al reaction – diffusion. The pack Al content was varied from 1 to 6 wt-% to investigate its effects on the coating formation process. It was found that the pack Al content in this range affected only the coating thickness and therefore the growth rate of the coating, but not the surface Al concentration. A post-aluminising heat treatment study was also undertaken for an aluminised specimen at 650°C under an argon atmosphere to investigate the kinetics of converting the brittle Fe 14 Al 86 and FeAl 3 phase layers to a more ductile FeAl phase layer. It was observed that this was a slow process requiring 1132 h for an initial coating layer thickness of 33μm. The coating after the conversion consisted of a uniform top FeAl layer with all other alloying elements in the solid solution and a diffusion zone underneath.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · High-Temperature Coating Behaviors · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Advanced Materials Research Institute School of Engineering and Technology, Northumbria University, Ellison Building, Ellison Place, Newcastle upon Tyne, NE1 8ST, UK

References (20)

Show source-provided references
1. ABE F. OkADA H. WANIKAWA S. TABUCHI M. ITAGAKI T. KIMURA K. and YAMAGUCHI K.: Proc. 1st Int. Conf. on ‘Advances in structural steels’ Tsukuba Japan May 2002.
2. ENNIS P. J. ZIELINSICALIPIEC A. WACHTER O. and CZYRSKA-FILEMONOWICZ A.: Acta Mater. 1997 45 4901–4907.10.1016/S1359-6454(97)00176-6 ↗
3. 10.1016/0921-5093(89)90428-010.1016/0921-5093(89)90428-0 ↗
4. 10.1149/1.209573210.1149/1.2095732 ↗
5. BAHADUR A., and MOHANTY o. N.: Mater. Trans., JIM, 1990, 31, 948–953.
6. 10.1016/S0257-8972(98)00529-510.1016/S0257-8972(98)00529-5 ↗
7. 10.1023/A:102052922396510.1023/A:1020529223965 ↗
8. 10.1016/j.surfcoat.2003.10.04610.1016/j.surfcoat.2003.10.046 ↗
9. 10.1023/A:101253422016510.1023/A:1012534220165 ↗
10. XIANG Z. D. BURNELLGRAY J. S. and DATTA P. K.: Surf Eng. 2001 17 287–294.10.1179/026708401101517890 ↗
11. SOLIMAN H. M., , MOHAMED K. E., , EL-AZIM M. E. ABD, and HAMMAD H. F.: J. Mater. Sci Technol, 1997, 13, 383–388.
12. 10.1179/02670830222500180410.1179/026708302225001804 ↗
13. 10.1149/1.240197610.1149/1.2401976 ↗
14. 10.1016/0040-6090(80)90501-510.1016/0040-6090(80)90501-5 ↗
15. 10.1016/S0257-8972(02)00044-010.1016/S0257-8972(02)00044-0 ↗
16. 10.1023/A:102591581292810.1023/A:1025915812928 ↗
17. 10.1179/02670830322500296510.1179/026708303225002965 ↗
18. 10.1016/S0257-8972(03)00790-410.1016/S0257-8972(03)00790-4 ↗
19. 10.1023/A:102114941301710.1023/A:1021149413017 ↗
20. 10.7567/JJAPS.24S2.13410.7567/JJAPS.24S2.134 ↗