journal article·2007-09

Preparation of semisolid A356 alloy feedstock cast through vertical pipe

X. R. Yang, W. M. Mao, S. Pei

Materials Science and Technology· Volume 23· Issue 9
Publisher page

Abstract

It is demonstrated that the fine spheroidal and equiaxed non-dendritic microstructures required for semisolid casting can be formed by using a vertical pipe. Various pouring temperatures (615–660°C) and cooling rates of the vertical pipe (no, 200, 400°C preheat) were used to investigate their influence on the semisolid microstructure of an A356 alloy. The results indicate that suitable semisolid billets can be generated at both lower and higher pouring temperatures; thus the vertical pipe technique may be readily exploited in industrial applications. The results also reveal that the microstructure is affected significantly by the cooling effect of the vertical pipe. Furthermore, in the longitudinal section, non-uniform grain sizes were observed, namely the primary α-Al at the bottom of the billet was coarser than that at the top, an effect attributed to the differences of solidification time and cooling rate. The relevant mechanisms are discussed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. 10.1007/BF0266109010.1007/BF02661090 ↗
2. 10.1016/S0921-5093(97)00758-210.1016/S0921-5093(97)00758-2 ↗
3. Brusethaug S., and Vole J.: Proc. 6th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Turin, Italy, September 2000, Polytechnic of Turin,451–456.
4. 10.1016/0921-5093(95)09861-510.1016/0921-5093(95)09861-5 ↗
5. Lukasson M. · AFS Trans · 2002 · 110 · 271
6. Kaufmann H. · Aluminum · 2000 · 76 · 70
7. Potzinger R., Kaufmann H., and Uggowitzer P. J.: Proc. 6th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Turin, Italy, September 2000, Polytechnic of Turin,85–90.
8. Haga T.: Proc. 7th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Tsukuba, Japan, September 2002, National Institute of Advanced Industrial Science and Technology,107–112.
9. Apelian D.: Proc. 7th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Tsukuba, Japan, September 2002, National Institute of Advanced Industrial Science and Technology,25–30.
10. Apelian D. · Die Cast. Eng · 2004 · 1 · 22
11. Forn A., and Baile M. T.: Proc. 8th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Limassol, Cyprus, September 2004, University of Cyprus, Worcester Polytechnic Institute (USA), Paper16–1.
12. Wang H., StJohn D. H., Davidson C. J., and Ning Z.: Proc. 8th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Limassol, Cyprus, September 2004, University of Cyprus, Paper14–3.
13. Cai W. H. · J. Nanchang Univ. (Eng. Technol) (China) · 2003 · 25 · 13
14. Motegi T., and Tanabe F.: Proc. 8th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Limassol, Cyprus, September 2004, University of Cyprus, Paper16–4.
15. Pahlevani F., Salarfar S., and Nili-Ahmadabadi M.: Proc. 8th Int. Conf. on ‘Processing of semi-solid alloys and composites’, Limassol, Cyprus, September 2004, University of Cyprus, Paper11–2.
16. 10.1179/02670830110151038410.1179/026708301101510384 ↗
17. 10.1179/02670839910150618410.1179/026708399101506184 ↗
18. 10.1016/j.scriptamat.2005.03.01710.1016/j.scriptamat.2005.03.017 ↗
19. 10.1016/S0921-5093(00)00619-510.1016/S0921-5093(00)00619-5 ↗
20. Chalmers B. · J. Aust. Inst. Met · 1963 · 8 · 255
21. Ohno A. ‘The solidification of metals’; 1976, Tokyo, Chijin Shokan.
22. Jackson K. A. · Trans. Metall. Soc. AIME · 1966 · 236 · 149