journal article·2016-03

Microstructural aspects of wear behaviour of TiC coated low alloy steel

A. N. Md Idriss, M. A. Maleque, I. I. Yaacob, R. M. Nasir, S. Mridha, T. N. Baker

Materials Science and Technology· Volume 32· Issue 4
Publisher page

Abstract

A comparison of the room temperature wear behaviour of untreated low alloy steel surfaces with those containing TiC powders was conducted against an alumina ball. The coefficient of friction, the wear rate and the severity of the damage on the surface were assessed. Incorporation of powders produced a hardness 2.6 times greater and a wear rate 21 times less than the untreated steel. Friction from the third body abrasion and protruding carbides of the processed steel resulted in mild wear with a steady state coefficient friction of 0.4. Both samples showed surface chemical reactivity with the environment as a result of the generation of flash temperature producing an oxide layer, which influenced wear.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Tribology and Wear Analysis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Advance Materials and Surface Engineering Research Unit, Department of Manufacturing and Materials Engineering, International Islamic University of Malaysia, P.O. Box 10, 50728 Kuala Lumpur, Malaysia

USM School of Mechanical Engineering, Universiti Sains Malaysia, Seri Ampangan, 14300 Nibong Tebal Seberang Perai Selatan, Penang, Malaysia

Department of Mechanical and Aerospace Engineering, University of Strathclyde, James Weir Building, Glasgow G1 1XJ, UK

Funding

Research Management Center (RMC) of International Islamic University of Malaysia

References (21)

Show source-provided references
1. Olson D. L., and Cross C. E.: ‘Friction and wear in the mining and mineral industries’, ‘ASM handbook, friction, lubrication and wear technology’, Vol. 18, 549–555; 1992, Materials Park, OH, ASM International.
2. 10.1016/0043-1648(84)90069-310.1016/0043-1648(84)90069-3 ↗
3. 10.1179/02670839679016598410.1179/026708396790165984 ↗
4. 10.1016/S0924-0136(96)02660-X10.1016/S0924-0136(96)02660-X ↗
5. Mridha S., , Md Idriss A. N., , Maleque M. A., , Suryanto, , and Souad A.: ‘Effect of voltage on the consolidation of TiC particulates on steel substrate fused by TIG welding arc’, Int. J. Mech. Mater. Eng., 2012, 7, 48–53.
6. Mridha S. Md Idriss A. N. and Baker T. N.: ‘Incorporation of TiC particles on AISI 4340 low alloy steel surfaces via tungsten inert gas arc melting’ Adv. Mater. Res. 2012 445 655–660. doi: 10.4028/www.scientific.net/AMR.445.65510.4028/www.scientific.net/AMR.445.655 ↗
7. Mridha S. and Md Idriss A. N.: ‘Microstructure of TIG melted composite coating produced using 1.0 and 1.5 mg/mm2 TiC at an energy input of 2640 J/mm’ Adv. Mater. Res. 2012 576 463–466. doi: 10.4028/www.scientific.net/AMR.576.46310.4028/www.scientific.net/AMR.576.467 ↗
8. 10.1016/j.surfcoat.2006.10.04210.1016/j.surfcoat.2006.10.042 ↗
9. http://www.us-nano.com/inc/sdetail/200.
10. 10.1016/S0043-1648(02)00051-010.1016/S0043-1648(02)00051-0 ↗
11. 10.1179/1743284714Y.000000053010.1179/1743284714Y.0000000530 ↗
12. 10.1179/1743284714Y.000000071210.1179/1743284714Y.0000000712 ↗
13. Hutchings I. M.: ‘Tribology friction and wear of engineering materials’, 135–150; 1992, London, Edward Arnold.
14. 10.1016/0043-1648(89)90109-910.1016/0043-1648(89)90109-9 ↗
15. 10.1016/0043-1648(95)06896-110.1016/0043-1648(95)06896-1 ↗
16. 10.1016/S0043-1648(98)00407-410.1016/S0043-1648(98)00407-4 ↗
17. 10.1016/0043-1648(81)90137-X10.1016/0043-1648(81)90137-X ↗
18. 10.1016/S0301-679X(98)00027-910.1016/S0301-679X(98)00027-9 ↗
19. 10.1016/j.wear.2010.12.00710.1016/j.wear.2010.12.007 ↗
20. 10.1016/j.triboint.2014.02.00210.1016/j.triboint.2014.02.002 ↗
21. 10.1016/S0043-1648(97)00197-X10.1016/S0043-1648(97)00197-X ↗