journal article·2008-03

Residual stress relaxation in shot peened high strength low alloy steel

A. Turnbull, J. J. Pitts, J. D. Lord

Materials Science and Technology· Volume 24· Issue 3
Publisher page

Abstract

The relaxation of residual stress in a shot peened high strength low alloy steel in response to applied loads has been investigated for both single shot and cyclic loading. The near surface residual stress was measured predominantly by X-ray diffraction (first 10 μm) but supplemented for some conditions by measurements using high resolution, fine increment hole drilling to yield depth profiling. The compressive residual stress showed a peak at ∼50 μm below the surface. Under single shot compressive loading, relaxation became significant when the combined surface and applied compressive stresses exceeded the proportional limit of the unpeened surface. The steel showed good resistance to residual stress relaxation under cyclic loading conditions, with only a 13% decrease despite cyclic load amplitudes at 50% of the 0˙2% proof stress in compression. Significant relaxation did occur at applied stress amplitudes of ∼80% of the 0˙2% proof stress in compression. While large single shot or cyclic stresses would represent rare occurrences, they could lead to a marked loss in beneficial compressive stress and should be accounted for in structural integrity assessment.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Surface Treatment and Residual Stress · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. Gangloff R. P.: in ‘Hydrogen assisted cracking, comprehensive structural integrity’, (eds. J. Petit and P. Scott),Vol. 6, 31–101; 2003, London, Elsevier.10.1016/B0-08-043749-4/06134-6 ↗
2. Mordfin L. (ed.): ‘Mechanical relaxation of residual stresses’, ASTM STP 993, Philadelphia, PA, 1988.10.1520/STP993-EB ↗
3. Kodama S.: Proc. Int. Conf. on ‘Mechanical behaviour of metals II’, 111-118; 1972, Kyoto, Society of Material Science.
4. James M. R. · Adv. Surf Treat. Technot Appl Effects · 1987 · 4 · 349
5. Iida K. · Weld World · 1997 · 39 · 138
6. 10.1016/S0921-5093(98)00522-X10.1016/S0921-5093(98)00522-X ↗
7. 10.1016/S0921-5093(98)01165-410.1016/S0921-5093(98)01165-4 ↗
8. 10.4028/www.scientific.net/MSF.347-349.37410.4028/www.scientific.net/MSF.347-349.374 ↗
9. 10.1016/S0921-5093(00)01035-210.1016/S0921-5093(00)01035-2 ↗
10. Zhaung W. · Int. J. Fatig · 2001 · 23
11. 10.1016/S0142-1123(00)00104-310.1016/S0142-1123(00)00104-3 ↗
12. Lohe D., and Vohringer O.: in ‘Handbook of residual stress and deformation of steel’, (ed. G. Totten etal.), 54-69; 2002, Materials Park, OH, ASM.
13. 10.1179/02670830222500466710.1179/026708302225004667 ↗
14. 10.1016/S0921-5093(01)01915-310.1016/S0921-5093(01)01915-3 ↗
15. Belassel M. · Proc. Int. Conf. on ‘Fatigue damage of materials’
16. 10.4028/www.scientific.net/KEM.274-276.87110.4028/www.scientific.net/KEM.274-276.871 ↗
17. Turnbull A. ‘Integrity of shot-peened high strength steel compo-nents in the context of residual stress relaxation and hydrogen uptake’, NPL Report DEPC MPE 022, 2005
18. Grant P. V., Lord J. D., and Whitehead P. S. ‘The measurement of residual stresses by the incremental hole drilling technique’, NPL measurement good practice guide No. 53, Issue 2, 2006.
19. Kandil F. A.