journal article·2011-01

Influence of tin and bismuth on machinability of lead free 6000 series aluminium alloys

G. Timelli, F. Bonollo

Materials Science and Technology· Volume 27· Issue 1
Publisher page

Abstract

The present paper presents the microstructural characteristics of an extruded AA6012A-T6 (AlMgSiBiSn) alloy and the microstructural changes occurring during turning operations, analysing the mechanism involved in chip breaking. An experimental investigation has been conducted to determine the effects of different cutting speed and feedrate on the machinability of the alloy. The machinability of the AA6012A-T6 alloy, where Pb is substituted by Bi and Sn, has then been compared to the standard AA6012-T6 (AlMgSiPb) and AA6082-T6 (AlSiMg) alloys. The results indicate that the extensive plastic deformation induces a preferred orientation of the grain structure and secondary phases along the shear plane, and a local increase in the alloy temperature. Low melting point compounds, such as the Sn and Bi bearing particles, transform into a soft or liquid state, changing their initial compact shape to assume a needle-like morphology. The β-Mg2Si and α-Al(FeMn)Si particles are not influenced by the working temperature and keep their initial shape. The AA6082-T6 alloy shows a very poor machinability, with long and continuous strips, while the AA6012A-T6 alloy reveals a good chip formation with small and discontinuous C shaped chips, similar to the AA6012-T6 (AlMgSiPb) alloy. In particular, a feedrate higher than 0·2 mm rev−1 provides short and suitable chips, independently of cutting speed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Management and Engineering, University of Padova, Stradella S. Nicola, 3 I 36100 Vicenza, Italy

References (26)

Show source-provided references
1. Kalpakjian S., and Schmid S. R. ‘Manufacturing processes for engineering materials’, 4th edn, 416–514; 2003, Upper Saddle River, NJ, Pearson Education Inc.
2. 10.1016/S0924-0136(97)00081-210.1016/S0924-0136(97)00081-2 ↗
3. 10.1016/S0890-6955(03)00199-810.1016/S0890-6955(03)00199-8 ↗
4. 10.1016/S0890-6955(03)00200-110.1016/S0890-6955(03)00200-1 ↗
5. 10.1016/0924-0136(95)01911-110.1016/0924-0136(95)01911-1 ↗
6. 10.1016/S0924-0136(96)02433-810.1016/S0924-0136(96)02433-8 ↗
7. Muhsin I. S. ‘The role of the contact length as a governing factor in cutting process’, PhD thesis, Royal Institute of Technology, Stockholm, Sweden, 1991.
8. in ‘ASM Handbook’, Vol. 16, ‘Machining of aluminum and aluminum alloys’, (ed. Davis J. R.), 761–804; 1989, Materials Park, OH, ASM International.10.31399/asm.hb.v16.a0002184 ↗
9. Bray J. W.: in ‘Aluminum mill and engineered wrought products’ (ed. Rooy E.L.), Vol. 2, 17–483; 1989, Materials Park, OH, ASM International.
10. 10.1016/S0921-5093(03)00521-510.1016/S0921-5093(03)00521-5 ↗
11. Sircar S. ‘Free machining aluminum alloy containing bismuth or bismuth-tin for free machining and a method of use’, US patent no. 6409966, Reynolds Metals Company, Richmond, VA, USA, 2002.
12. Sircar S. ‘Free-machining aluminum alloy and method of use’, US patent no. 6315947, Reynolds Metals Company, Richmond, VA, USA, 2001.
13. Bartges C. W., and Klemp T. J. ‘Lead-free 6XXX aluminium alloy’, European patent no. 1464717, Alcoa Center, PA, USA, 2004.
14. Farrar L. E., and Coats N. L. ‘Lead-free 6000 series aluminum alloy’, US patent no. 5810952, Kaiser Aluminum and Chemical Corporation, Oakland, CA, USA, 1998.
15. 10.4028/www.scientific.net/MSF.396-402.120510.4028/www.scientific.net/MSF.396-402.1205 ↗
16. Koch S. · BHM · 2008 · 153 · 278
17. Timelli G., Faresin B., Bonollo F., Fantinel C., and de Cet S.: Proc. 32th AIM National Conf., Ferrara, Italy, September 2008, University of Ferrara, Paper 126.
18. 10.31399/asm.tb.mpp.978162708260010.31399/asm.tb.mpp.9781627082600 ↗
19. ‘Tool-life testing with single-point turning tools’, Standard 3685, ISO Geneva, Switzerland, 1993.
20. Reiso O. · Mater. Forum · 2004 · 28 · 32
21. Jaspers S. ‘Metal cutting mechanics and material behaviour’, PhD thesis, Eindhoven: Tecnishe Universiteit Eindhoven, Eindhoven, the Netherlands, 1999.
22. de Haas Marc-Jan: ‘Grain boundary phenomena and failure of aluminium alloys’, PhD thesis, University of Groningen, Groningen, the Netherlands, 2002.
23. Shaw M. C. ‘Metal cutting principles’, 2nd edn; 1984, New York, Oxford University Press.
24. 10.1016/S0921-5093(02)00073-410.1016/S0921-5093(02)00073-4 ↗
25. 10.1016/S0921-5093(03)00103-510.1016/S0921-5093(03)00103-5 ↗
26. Xie Q. ‘Mechanics of metal cutting through a solid mechanics approach; adiabatic shear banding’, PhD thesis, Washington State University, Washington, USA, 1995.