Influence of solutionising and aging temperatures on microstructure and mechanical properties of cast Al–Si–Cu alloy
Source abstract
Abstract
This paper presents the influence of solution and aging temperatures on the microstructure and mechanical properties of 319 secondary cast aluminium alloy. Experimental alloy was subjected to different heat treatment cycles. Heat treatments were designed with two solutionising temperatures (504 and 545°C) at two solutionising times (4 and 8 h), followed by quenching in water at 60°C and artificial aging. The artificial aging was carried out at two temperatures (200 and 154°C) for 6 h. The improvement in mechanical properties was obtained with low solution temperature (504°C) for 8 h followed by quenching in water to 60°C and aging at low temperature (154°C). The increase in the solutionising temperature from 504 to 545°C was recommendable only for short solutionising time (4 h). Increase in the aging temperature from 154 to 200°C has led to the increase in hardness with the corresponding decrease in ductility. Aging under unfavourable conditions (prolonged aging at high temperature) caused coarsening of spheroidised eutectic silicon crystals and precipitated particles resulted in deleterious effect on the tensile strength.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Maestría en Procesos y MaterialesUniversidad Autónoma de Zacatecas, Av. López Velarde # 801, Centro, Zacatecas, Zac., 98060, México
Department of Mechanical and Industrial EngineeringIndian Institute of Technology (IIT), Roorkee, UA 247667, India;, Email: dkd04fme@iitr.ernet.in
Instituto Tecnológico de Zacatecas, C.P. 98000, Zacatecas Zac. México
References (15)
Show source-provided references
1. Kaufman J. G., and Rooy E. L. ‘Aluminum alloy castings, properties, processes and applications’, Chapter 12, 13; 2005, Materials Park, OH, USA, AFS and ASM International.10.31399/asm.tb.aacppa.9781627083355 ↗
2. ‘Aluminum casting technology’, 2nd edn, 66-67; 2001, Des Plaines, IL, USA, AFS, Inc.
3. Kashyap K. T. et al. Materials Science and Technology, 9, 1993, 18910.1179/mst.1993.9.3.189 ↗
4. ‘Aluminum casting technology’, 2nd edn, 287; 2001, Des Plaines, IL, USA, AFS, Inc.
5. 10.1016/S0167-577X(03)00270-210.1016/S0167-577X(03)00270-2 ↗
6. 10.1016/j.scriptamat.2004.11.01210.1016/j.scriptamat.2004.11.012 ↗
7. 10.1081/AMP-20005513810.1081/AMP-200055138 ↗
8. Sharma R., Kumar A., and Dwivedi D. K.: Mater. Sci. Eng. A, 2005, A408, (1-2),274–280.
9. 10.1080/1042691050046478410.1080/10426910500464784 ↗
10. 10.1179/136404606X15386710.1179/136404606X153867 ↗
11. 10.1016/j.matdes.2006.04.01210.1016/j.matdes.2006.04.012 ↗
12. 10.1016/j.matdes.2006.04.01110.1016/j.matdes.2006.04.011 ↗
13. Dwivedi D. K. · Inst. Eng. (India) · 2002 · 83 · 46
14. Dwivedi D. K. · Aluminium India · 2000 · 28 · 21
15. ‘Standard methods of tension testing wrought and cast aluminum and magnesium-alloy products’, 1984, Designation B 557-84, ASTM, Philadelphia, PA, USA.