Dwell time effect on fatigue crack growth of RR1000 superalloy
Source abstract
Abstract
The requirement for improved understanding of the behaviour of turbine disc alloys at elevated temperatures has led to an increased interest in the contribution of time dependant mechanisms to high temperature fatigue crack growth. A study has been conducted on a new powder alloy to investigate the contribution of such mechanisms when the applied waveform is varied in terms of hold periods and the influence of limited thermal exposure is included. Variable waveform tests performed in air at 725°C have indicated that the addition of a hold time at maximum load in a fatigue cycle tends to increase the crack growth rate per cycle in the as heat treated material. Crack growth in thermally exposed material is retarded by up to a 10 s hold time and then accelerated as the hold time increases further. Rapid near crack tip stress relaxation induced by γ′ coarsening is proposed to have a beneficial effect on the severity of this type of damage which causes the crack growth rate reduction for short hold times.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Fatigue and fracture mechanics · High Temperature Alloys and Creep · Mechanical Failure Analysis and Simulation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. 10.1016/0025-5416(82)90167-710.1016/0025-5416(82)90167-7 ↗
2. Ghonem H., and Zheng D.: Mater. Sci. Eng. A, 1992, A150,151–160.10.1016/0921-5093(92)90107-C ↗
3. Zhan Z. L., and Tong J.: in ‘Damage and fracture mechanics VIII’, (ed. C. A. Brebbia and A. Varvani-Farahani), 129-137; 2004, Wessex Institute of Technology.
4. Molins R., Chassaigne J., and Andrieu E.: Proc. 4th Int. Special Emphasis Symp. on ‘Superalloys 718, 625, 706 and various derivatives’, Pittsburgh, PA, USA, June 1997, TMS,655–664.10.7449/1997/Superalloys_1997_655_664 ↗
5. 10.1179/02670830110150937710.1179/026708301101509377 ↗
6. 10.1016/S0142-1123(98)00056-510.1016/S0142-1123(98)00056-5 ↗
7. Ponelle S., Brethes B., and Pineau A.: Proc. 9th Int. Spring Meet., 2001, European Structural Integrity Society,245–254.
8. Pang H. T. · 2002
9. Hunt D. W. · 2001
10. 10.1046/j.1460-2695.1998.00542.x10.1046/j.1460-2695.1998.00542.x ↗
11. 10.1007/s11661-002-0302-310.1007/s11661-002-0302-3 ↗
12. Andrieu E., Molins R., Ghonem H., and Pineau A.: Mater. Sci. Eng. A, 1992, A154,21–28.10.1016/0921-5093(92)90358-8 ↗
13. Shahianian P., and Sadananda K.: Trans. ASME, 1979, 101, 224.230.10.1115/1.3443681 ↗
14. 10.1016/S0921-5093(01)01957-810.1016/S0921-5093(01)01957-8 ↗
15. Bowman R., and Antolovich S. D.: Proc. Conf. on ‘Superalloys 1988’, (ed. Reichman et al), 565-574; 1988, Seven Springs, PA, TMS.10.7449/1988/Superalloys_1988_565_574 ↗
16. 10.1007/BF0281171010.1007/BF02811710 ↗
17. 10.1111/j.1460-2695.1993.tb00767.x10.1111/j.1460-2695.1993.tb00767.x ↗
18. Pineau A.: Proc. Conf. on ‘Engineering against fatigue’, (ed. Benyon et al), 557-565; 1997, Sheffield, Balkema.
19. Liu X., Kang B., and Chang K.: Mater. Sci. Eng. A, 2003, A340,8–14.