Fluidity of aluminium alloy AlSi7Mg–SiC particulate composite melts
Source abstract
Abstract
A spiral test was used to evaluate the flowability of an AlSi7 Mg0·6 alloy reinforced via 10–30 vol.-%SiC particles having average diameters of 9, 13, and 23 μm. The results show that the composite melt has the same ability to flow into long thin sections as unreinforced aluminium, when the particle content is <20 vol.-%. The flowability of the particulate metal matrix composite is significantly reduced for particle volume fractions >20 vol.-% and approaching 30 vol.-% as a result of increased viscosity. At these higher levels of SiC, an increase in pouring temperature cannot compensate for the reduced flowability. The particle distribution in the solidified material depends on the length which the metal flows before solidification. After 150–200 mm of flow, dendritic grains growing in the composite melt push the particles so that the solidified microstructure consists of open areas without particles. The particle free areas increase in diameter with the flow distance.MST/3005
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Innovations in Concrete and Construction Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. FLEMINGS M. C. · Mod. Cast. · 1961 · 12 · 75
2. NIESSE J. E. · AFS Trans. · 1959 · 67 · 685
3. 10.1007/BF0265446610.1007/BF02654466 ↗
4. TUTTLE B. L. · AFS Trans. · 1989 · 97 · 889
5. CAPADONA J. A. · AFS Trans. · 1985 · 94 · 43
6. RAGONE D. V. · AFS Trans. · 1956 · 64 · 640
7. FRIEBEL V. R. · AFS Trans. · 1962 · 70 · 573
8. BASTIEN P. · AFS Trans. · 1962 · 70 · 400
9. 10.1179/imr.1992.37.1.10110.1179/imr.1992.37.1.101 ↗
10. CARITY R. E. · AFS Trans. · 1990 · 743
11. ROHATGI P. · Mod. Cast. · 1988 · 47
12. 10.1179/imtr.1986.31.1.11510.1179/imtr.1986.31.1.115 ↗
13. SURAPPA M. K. · Tecnometal. · 1977 · 4 · 33
14. RICHTER D. · Adv. Mater. Technol. Int. · 1992 · 60 · 57
15. 10.1016/0921-5093(93)90223-210.1016/0921-5093(93)90223-2 ↗
16. 10.1016/0095-8522(65)90016-410.1016/0095-8522(65)90016-4 ↗
17. ASSAR A. · Aluminium · 1981 · 57 · 807
18. 10.1016/0266-3538(89)90093-610.1016/0266-3538(89)90093-6 ↗
19. LANG G. · Aluminium · 1972 · 48 · 664
20. WALKER B. · Foundry Trade J. · 1963 · 115 · 713
21. FLEMINGS M. C. · AFS Trans. · 1959 · 67 · 496
22. KONDIC V. · J. Inst. Met. · 1949 · 16 · 665
23. RAGONE D. V. · AFS Trans. · 1956 · 64 · 653
24. VENKATESWARAN S. · AFS Trans. · 1986 · 94 · 701
25. SHESHRADI M. R. · Mod. Cast. · 1965 · 21 · 110
26. CLARK K. L. · Trans. AFA · 1946 · 54 · 37
27. HUTTER L. · Giesserei · 1954 · 20 · 528
28. NORDMARK A. · Stoberiet · 1992 · 69 · 6
29. 10.1016/0921-5093(93)90218-410.1016/0921-5093(93)90218-4 ↗
30. A. KOLSGAARD: 'Casting characteristics of SiC particulate reinforced AlSi7Mg aluminium matrix composites', Thesis 1993: 120, Department of Machine Design and Materials Technology, Norwegian Institute of Technology.