journal article·2014-08

Evaluation of creep deformation behaviour of different microstuctural zones of 316LN SS weld joint using impression creep testing technique

Naveena V. D. Vijayanand, V. Ganesan, K. Laha, M. D. Mathew

Materials Science and Technology· Volume 30· Issue 10
Publisher page

Abstract

Impression creep technique, which uses flat ended cylindrical indenter, is an attractive material non-invasive technique for evaluating creep properties as it enables probing small volume of material and requires short time for testing. The present investigation discusses the application of impression creep technique for characterising the creep behaviour of different microstructural regions in a high nitrogen grade of 316LN SS weld joint. Impression creep tests were carried out at 923 K on the weld metal, the base metal and the heat-affected zone in 316LN SS weld joint. The impression creep curves exhibited the first two characteristic stages of the creep processes, namely, a primary creep stage and a secondary creep stage. The rate at which the cylindrical flat punch penetrated into the test specimen was controlled by the time dependence of the movement of the material underneath the punch. The weld metal, the base metal and the heat affected zone exhibited distinct creep behaviour. The difference in creep behaviour of each zone was correlated with the difference in microstructure and morphology of the weld joint. A comparison was made between the data obtained from impression creep tests and from independent uniaxial creep tests on the weld metal and the base metal. A good correlation was established between impression creep and uniaxial creep results.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals · Nuclear Materials and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Mechanical Metallurgy Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, India

References (25)

Show source-provided references
1. 10.1007/s11665-012-0290-410.1007/s11665-012-0290-4 ↗
2. 10.1016/j.msea.2012.05.01710.1016/j.msea.2012.05.017 ↗
3. Naveena and Mathew MD: ‘Effect of nitrogen on creep deformation behavior of type 316LN stainless steel: studies using impression creep technique’, Proc. 12th Int. Conf. on ‘Creep and fracture of engineering materials and structures’, Kyoto, Japan, May 2012, The Japan Institute of Metals, Paper B18.
4. Wang SH · J. Mater. Sci. Technol. · 1994 · 17
5. 10.1179/mht.1999.01110.1179/mht.1999.011 ↗
6. Gibbs WS · Weld. Res. Suppl. · 1985 · 153
7. 10.1016/j.msea.2005.05.11010.1016/j.msea.2005.05.110 ↗
8. Sun W · Acta. Metall. Sin. · 1999 · 12 · 68
9. Mannan SL · Trans. IIM · 2003 · 56 · 155
10. 10.1007/BF0055224110.1007/BF00552241 ↗
11. 10.1016/0025-5416(79)90164-210.1016/0025-5416(79)90164-2 ↗
12. 10.1007/BF0055224310.1007/BF00552243 ↗
13. 10.1557/JMR.1994.090310.1557/JMR.1994.0903 ↗
14. 10.1016/S0921-5093(03)00205-310.1016/S0921-5093(03)00205-3 ↗
15. 10.1016/j.msea.2005.08.03110.1016/j.msea.2005.08.031 ↗
16. 10.1016/j.msea.2009.11.05310.1016/j.msea.2009.11.053 ↗
17. 10.1016/j.msea.2005.03.11910.1016/j.msea.2005.03.119 ↗
18. Etienne CF, Rossum O and Roode F: ‘Creep of welded joints AISI 316’, Proc. Int. Conf. on ‘Engineering aspects of creep’, Sheffield, UK, September 1980, University of Sheffield, Vol. 2, 113–121.
19. Marshall P: ‘Austenitic stainless steels: microstructure and mechanical properties’; 1984, New York, Elsevier Applied Science.
20. 10.1016/S0022-3115(99)00057-410.1016/S0022-3115(99)00057-4 ↗
21. Garofalo F · Trans. AIME · 1964 · 230 · 1460
22. Al-Ganainy GS · Egypt. J. Solids · 2000 · 23 · 33310.21608/ejs.2000.151744 ↗
23. 10.1179/03063458379042759510.1179/030634583790427595 ↗
24. 10.1016/j.msea.2011.12.04410.1016/j.msea.2011.12.044 ↗
25. 10.1557/JMR.1996.019110.1557/JMR.1996.0191 ↗