Microstructural evolution during initial stage of high strain rate superplastic deformation in powder metallurgical 7475 Al–0·7Zr alloy
Source abstract
Abstract
The 7475 Al–0·7Zr (wt-%) cold rolled alloy sheet fabricated by powder metallurgy exhibited remarkable superplasticity for strain rates between 2×10−3 and 3×10−1 s−1 at 793 K. During the initial deformation stage, the strain rate sensitivity m increased with increasing strain and attained a value greater than 0·5 after about 50% elongation. Thus, the microstructural evolution which occurred during this initial deformation stage was examined, especially at high strain rates. On heating to the tensile testing temperature of 793 K, the alloy developed a very fine subgrain structure, stabilised with finely dispersed Al3Zr precipitate particles. The average subgrain size was less than 1 μm, and the misorientation angle of most subboundaries was less than 5°. In the initial deformation stage showing an increase in m value, the subboundary misorientations and, thus, the contribution of boundary sliding tended to increase with strain. Even the subboundaries with misorientation of 5–15° could play an important role through boundary sliding in the limited strain rate range showing superplasticity. Subgrains rotated as a group owing to the different sliding rates at different boundary misorientations, including those of original grain boundaries. The accommodation dislocations for the boundary sliding were absorbed into the subboundaries. Both subgrain rotation and dislocation absorption were considered to contribute greatly to the increase in subboundary misorientation.MST/1367
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. MATSUKI K. · J. Jpn Soc. Technol. Plast., · 1986 · 27 · 415
2. MATSUKI K. · Z. Metallkd., · 1988 · 79 · 231
3. 10.1016/S0036-9748(88)80310-710.1016/S0036-9748(88)80310-7 ↗
4. MATSUKI K. · J. Jpn Inst. Met., · 1973 · 37 · 44810.2320/jinstmet1952.37.4_448 ↗
5. 10.1179/03063457679043242510.1179/030634576790432425 ↗
6. 10.1007/BF0264234010.1007/BF02642340 ↗
7. 10.1016/0036-9748(76)90147-210.1016/0036-9748(76)90147-2 ↗
8. 10.1179/msc.1979.13.3-4.21110.1179/msc.1979.13.3-4.211 ↗
9. 10.1007/BF0281198110.1007/BF02811981 ↗
10. 10.1002/pssa.1970002022210.1002/pssa.19700020222 ↗
11. MATSUKI K. · J. Jpn Inst. Met., · 1981 · 45 · 93510.2320/jinstmet1952.45.9_935 ↗
12. STEVENS It. N. · Trans. AIME · 1966 · 236 · 1762
13. 10.1007/BF0264377110.1007/BF02643771 ↗
14. 10.1016/0036-9748(83)90275-210.1016/0036-9748(83)90275-2 ↗
15. WATTS B. M. · Met. Sci., · 1976 · 10 · 198
16. 10.1007/BF0054744110.1007/BF00547441 ↗
17. 10.1080/0141861790823486710.1080/01418617908234867 ↗
18. 10.1016/0001-6160(88)90275-110.1016/0001-6160(88)90275-1 ↗
19. MAHONEY F. A. · J. Mater. Sc · 1983 · 582
20. MURTY G. S. · Superplasticity and superplastic forming'