Formability of two aluminium alloys
Source abstract
Abstract
The suitability of two recently developed aluminium alloys (an Al–Mg–Mn alloy and an Al–Li–Cu alloy) for press forming applications has been examined. The characterisation involved the experimental determination of microstructural aspects, tensile properties, and formability parameters such as average plastic strain ratio and planar anisotropy. The forming limit diagram has been experimentally evaluated. A detailed analysis of the strain distribution profiles obtained from punch stretching experiments has been attempted. An attempt has been made to correlate the crystallographic texture with the formability parameters. The fracture surfaces of the punch stretched samples were observed using scanning electron microscopy with a view to obtaining a correlation between fracture behaviour and formability. The alloys, in particular the Al–Mg–Mn alloy, have been found to possess good stretchability but both show very limited drawability. Texture analysis indicated negligible earing during deep drawing. These alloys are suitable for stamping applications where stretching constitutes the major proportion of the deformation.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
The Department of Metallurgical EngineeringIndian Institute of Technology, Madras, 600 036, India
References (25)
Show source-provided references
1. 10.1007/BF0265643410.1007/BF02656434 ↗
2. LIU Y. C. · Metall. Trans · 1984 · 16 · 153110.1007/BF02658687 ↗
3. 10.1179/imr.1982.27.1.30710.1179/imr.1982.27.1.307 ↗
4. HECKER S. S. · Sheet Met. Ind · 1975 · 52 · 671
5. GHOSH A. K. · Met. Eng. Q · 1975 · 15 · 53
6. 10.1007/BF0265348210.1007/BF02653482 ↗
7. LIU Y. · Z. Metallkd · 1992 · 83 · 47
8. 10.1115/1.344326310.1115/1.3443263 ↗
9. ROBERTSON I. M. · Mater. Forum · 1991 · 15 · 102
10. 10.1007/BF0264432110.1007/BF02644321 ↗
11. 10.1016/0020-7403(73)90068-410.1016/0020-7403(73)90068-4 ↗
12. 10.1007/BF0070144110.1007/BF00701441 ↗
13. 10.1007/BF0115459910.1007/BF01154599 ↗
14. 10.1115/1.290339810.1115/1.2903398 ↗
15. 10.1016/0378-3804(87)90033-710.1016/0378-3804(87)90033-7 ↗
16. N. M. WANG and M. L. WERNER: in ‘Mechanics of sheet metal forming’, (ed. D. P. Koistinen and N. M. Wang), 367; 1978, New York, Plenum.10.1007/978-1-4613-2880-3_15 ↗
17. 10.1179/msc.1974.8.1.18510.1179/msc.1974.8.1.185 ↗
18. BLADE J. C. · J. Aust. Inst. Met · 1967 · 12 · 55
19. w BUNK · Z. Metallkd · 1965 · 56 · 645
20. BLADE J. C. · Trans. Jpn Inst. Met · 1962 · 90 · 374
21. 10.1179/mst.1989.5.2.18610.1179/mst.1989.5.2.186 ↗
22. 10.1179/mst.1994.10.7.58110.1179/mst.1994.10.7.581 ↗
23. SWAMINATHAN K. · Met. Mater. Process · 1989 · 1 · 49
24. 10.1007/BF0264450610.1007/BF02644506 ↗
25. 10.1016/0924-0136(92)90244-M10.1016/0924-0136(92)90244-M ↗