journal article·1989-09

Mechanical properties of Al–Li alloys Part 2 Fatigue crack propagation

K. T. Venkateswara Rao, R. O. Ritchie

Publisher page

Abstract

Mechanisms influencing the ambient temperature mechanical properties of commercial Al–Li alloys 2090, 2091, 8090, and 8091 are examined, with specific emphasis on the role of microstructure. In Part 2, results on fatigue crack propagation behaviour are presented for both ‘long’ (≥ 5 mm) and ‘microstructurally small’ (~1–1000 μm) cracks and compared with behaviour in traditional high strength aluminium alloys. In general, it is found that the growth rates of long fatigue cracks in Al–Li alloys are up to two to three orders of magnitude lower than in traditional 7000 and 2000 series alloys, when compared at an equivalent stress intensity range ∆K. By contrast, corresponding growth rates of microstructurally small fatigue cracks were up to two to three orders of magnitude higher than the long crack results. Such observations are attributed to the prominent role of crack tip shielding in Al–Li alloys resulting from the tortuous and deflected nature of the crack paths which results in a reduced crack tip ‘driving force’ from crack deflection and, more importantly, from the consequent crack closure induced by the wedging of fracture surface asperities. Since microstructurally small cracks are unable to develop the same level of shielding from crack closure by virtue of their limited wake, small crack growth rates are significantly accelerated. Unlike fracture toughness behaviour, artificial aging of commercial Al–Li alloys to peak strength has a mixed influence on the (long crack) resistance. Although behaviour at higher growth rates is relatively unaffected, in 2091 nominal threshold ∆KTH values are increased by 17%, whereas in 8090 and 8091 they are decreased by 16–17%. However, all alloys show reduced effective fatigue thresholds at peak strength after correcting for crack closure.MST/926b
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Fatigue and fracture mechanics · Aluminum Alloy Microstructure Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. HARRIS S. J. · Aluminum-lithium alloys IT' (Conf. Proc.),
2. BRETZ P. E. · Aluminum-lithium alloys II' (Conf. Proc.),
3. PETERS M. · Aluminium-lithium alloys III' (Conf. Proc.), (ed. C. Baker at al.), 239-246; 1986, London, The Institute of Metals.
4. 10.1007/BF0266126710.1007/BF02661267 ↗
5. VASUDEVAN A. K. · Metall. Trans., · 1985 · 16 · 44310.1007/BF02814350 ↗
6. PETIT J. · 'Aluminium—lithium alloys III' (Conf. Proc.), (ed. C. Baker et al.), 257-262; 1986, London, The Institute of Metals.
7. 10.1016/0025-5416(84)90078-810.1016/0025-5416(84)90078-8 ↗
8. 10.1115/1.322593910.1115/1.3225939 ↗
9. 10.1007/BF0264926910.1007/BF02649269 ↗
10. 10.1016/0036-9748(86)90115-810.1016/0036-9748(86)90115-8 ↗
11. 10.1016/0036-9748(87)90322-X10.1016/0036-9748(87)90322-X ↗
12. VENKATESWARA RAO K. T. · Metall. Trans., · 1988 · 19 · 563
13. VENKATESWARA RAO K. T. · Mater. Sci. Technol., 1989, 5, this issue, 882-895.
14. R. O. RITCHIE and w. YU: in ‘Small fatigue cracks’, (ed. R. O. Ritchie and J. Lankford), 167; 1986, Warrendale, PA, The Metallurgical Society of AIME.
15. 10.1016/0013-7944(81)90116-810.1016/0013-7944(81)90116-8 ↗
16. 10.1016/0022-5096(81)90003-X10.1016/0022-5096(81)90003-X ↗
17. 10.1016/0025-5416(88)90547-210.1016/0025-5416(88)90547-2 ↗
18. 10.1007/BF0281605110.1007/BF02816051 ↗
19. 10.1007/BF0001261910.1007/BF00012619 ↗
20. 10.1007/BF0264480310.1007/BF02644803 ↗
21. 10.1007/BF0001970510.1007/BF00019705 ↗
22. 10.1007/BF0264368810.1007/BF02643688 ↗
23. 10.1007/BF0264709110.1007/BF02647091 ↗
24. 10.1016/0025-5416(88)90235-210.1016/0025-5416(88)90235-2 ↗
25. 10.1007/BF0264240910.1007/BF02642409 ↗
26. 10.1179/imtr.1984.29.1.44510.1179/imtr.1984.29.1.445 ↗
27. S. J. HUDAK and K. S. CHAN: in ‘Small fatigue cracks’, (ed. R. O. Ritchie and J. Lankford), 379; 1986, Warrendale, PA, The Metallurgical Society of AIME.
28. A. PINEAU: in ‘Small fatigue cracks’, (ed. R. O. Ritchie and J. Lankford), 191; 1986, Warrendale, PA, The Metallurgical Society of AIME.
29. M. R. JAMES and W. L. MORRIS: in ‘Small fatigue cracks’, (ed. R. O. Ritchie and J. Lankford), 145; 1986, Warrendale, PA, The Metallurgical Society of AIME.
30. J. LANKFORD and D. L. DAVIDSON: in ‘Small fatigue cracks’, (ed. R. O. Ritchie and J. Lankford), 51; 1986, Warrendale, PA, The Metallurgical Society of AIME.
31. R. P. GANGLOFF and R. P. WEI: in ‘Small fatigue cracks’, (ed. R. O. Ritchie and J. Lankford), 239; 1986, Warrendale, PA, The Metallurgical Society of AIME.
32. R. P. GANGLOFT and R. O. RITCHIE: in ‘Fundamentals of deformation and fracture’, (ed. B. A. Bilby et al.), 529; 1985, Cambridge, Cambridge University Press.
33. J. L. HORNG and M. E. FINE: in ‘Fatigue crack growth threshold concepts’, (ed. D. L. Davidson and S. Suresh), 115; 1984, Warrendale, PA, The Metallurgical Society of AIME.
34. 10.1111/j.1460-2695.1987.tb00211.x10.1111/j.1460-2695.1987.tb00211.x ↗