journal article·2001-11

Texture development in cold rolled and annealed C-Mn-Si and C-Mn-Al-Si TRIP steels

M. de Meyer, L. Kestens, B.C. de Cooman

Materials Science and Technology· Volume 17· Issue 11
Publisher page

Abstract

The texture of two transformation induced plasticity steels has been studied by means of crystallographic orientation mapping. Texture measurements were carried out on ferrite, bainite, and austenite. The polygonal ferrite and the bainite texture, both bcc, could be distinguished based on the image quality parameter of the electron backscattering diffraction measurement. Both bcc textures were very similar, the main difference being the more pronounced 111alpha ND ND=normal direction and 110alpha RD RD=rolling direction fibre textures in the polygonal ferrite. The fcc texture was a strong gamma deformation texture, characterised by the beta fibre. The presence of the alpha fibre confirmed the strong 110gamma ND direction, which was previously detected by means of X ray diffraction XRD. The measured fcc and bcc textures were used to calculate orientation distribution function transformations according the Bain, Kurdjumov-Sachs, and Nishiyama-Wasserman orientation relationships. The predicted cube component {001}gamma 100gamma, which was missing in the measured texture, of gammaret indicates a variant selection for the gammaalphaB transformation. In addition it was shown that crystallographic orientation mapping could be used to make reliable phase fraction determinations, which were previously based on the light optical microscopy of colour etched specimens. This also proves that XRD determination of gammaret is flawed owing to the strong texturing of all phases present in the microstructure.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Magnetic Properties and Applications · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

The Laboratory for Iron and Steelmaking Ghent University, Technologiepark 9, B- 9052 Zwijnaarde, Ghent. Marijke.DeMeyer@rug.ac.be; Bruno.DeCooman@rug.ac.be

References (12)

Show source-provided references
1. KURDJUMOV G. and G. SACHS: Z. Phys., 1930, 64, 225.
2. BAIN E. C.: Trans. AIME, 1924, 70, 25.
3. NISHIYAMA Z.: Sct Rep. Res. Inst. Tohoku Univ., 1934— 35, 23, 638.
4. WASSERMANN G.: Arch. Eisenhüttenwes., 1933, 16, 647.
5. GOURGUES A.-F. %FLOWER H. M. and LINDLEY T. C.: Mater. Sci. Technol 2000 16 26–40.10.1179/026708300773002636 ↗
6. 10.2355/isijinternational.39.81310.2355/isijinternational.39.813 ↗
7. MAHIEU J. CLAESSENS S. DE MEYER M. and B. C. DE COOMAN: Proc. Conf. on ‘Galvanised steel sheet forum — automotive’ London UK May 2000 The Institute of Materials 185–196.
8. RANDLE V. and O. ENGLER: ‘Introduction to texture analysis: macrotexture microtexture and orientation mapping’; 2000 Reading Gordon and Breach Science Publishers.10.1201/9781482287479 ↗
9. VAN HOUTTE P.: ‘The MTM—FHM software system version 2’ Users Manual; 1995 Leuveu Katholieke Universiteit Leuveu.
10. 10.1016/S0921-5093(98)00820-X10.1016/S0921-5093(98)00820-X ↗
11. DE MEYER M. VANDERSCHUEREN D. DE BLAUWE K. and DE COOMAN B. C.: Proc. 41st Conf. on ‘Mechanical working and steel processing’ Baltimore MD USA October 1999 ISS 483 —491.
12. KESTENS L. YOSHINAGA N. VANDERSCHUEREN D. and DE B. C. COOMAN: Proc. Conf. on ‘IF steels 2000’ Pittsburgh PA USA June 2000 Iron and Steel Society 271–278.