Mechanical properties of Al–Li alloys Part 1 Fracture toughness and microstructure
Source abstract
Abstract
Mechanisms influencing the ambient temperature mechanical properties of commercial Al–Li alloys 2090, 8090, 8091, and 2091 are examined as a function of plate orientation, with specific emphasis on the role of microstructure. In Part 1, results on the uniaxial tensile and plane strain fracture toughness properties are presented and the behaviour is discussed in terms of the role of the matrix and grain boundary precipitates, associated precipitate free zones (PFZs), and the occurrence of short-transverse delamination. It is seen that in general peak aged microstructures show an excellent combination of strength and toughness (L–T, T–L), equal to or exceeding that shown by traditional 2000 and 7000 series high strength aluminium alloys. The superior toughness of peak aged compared with naturally aged microstructures seems to be associated with widespread matrix precipitation of platelike precipitates (T 1 in Al–Li–Cu alloys and S in Al–Li–Cu–Mg alloys), β′-dispersoids and second phase particles which promote ductile (void coalescence) fracture, and with secondary cracking (through thickness delamination) caused by poor short transverse properties. By contrast, the deterioration in fracture toughness with overaging is primarily attributed to extensive grain boundary precipitation and corresponding formation of PFZs, similar to traditional aluminium alloys. All alloys show highly textured, predominantly unrecrystallised grain structures that render the properties to be strongly orientation dependent; specifically, fracture toughness values for the short-transverse orientations (S–L, S–T) are typically 50% lower than in the longitudinal and transverse orientations. MST/926a
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. SANDERS T. H. and STARKE E. A. (eds): ‘Aluminum—lithium alloys’ (Conf. Proc.); 1981 Warrendale PA The Metallurgical Society of AIME.
2. SANDERS T. H. and STARKE E. A. (eds): ‘Aluminum—lithium alloys II’ (Conf. Proc.); 1984 Warrendale PA The Metallurgical Society of AIME.
3. BAKER C. GREGSON P. J. S. J. HARRIS and C. J. PEEL (eds): ‘Aluminium—lithium alloys III’ (Conf. Proc.); 1986 London The Institute of Metals.
4. CHAMPIER C. DUBOST B. MIANNAY D. and L. SABETAY (eds): in ‘4th international aluminium—lithium conference'; 1987 Orsay Les Editions de Physique (J. Phys. 1987 48 coll. C3 suppl. 9).10.1051/jphyscol:19873106 ↗
5. STARKE E. A, , SANDERS T. H. and 1. G. PALMER: J. Met., 1981, 32, 24.
6. 10.1007/BF0266126710.1007/BF02661267 ↗
7. GREGSON P. J. and FLOWER H. M.: Acta Metall. 1985 33 527.10.1016/0001-6160(85)90095-1 ↗
8. HARRIS S. J. NOBLE B. and DINSDALE K.: in ‘Aluminium—lithium alloys II’ (Conf. Proc.) (ed. Sanders T. H. and Starke E. A.) 219; 1984 Warrendale PA The Metallurgical Society of AIME.
9. 10.1007/BF0264471510.1007/BF02644715 ↗
10. SURESH S. VASUDLVAN A. K. TOSTEN M. and HOWELL P. R.: Acta Metall. 1987 35 25.10.1016/0001-6160(87)90210-0 ↗
11. 10.1016/0025-5416(84)90078-810.1016/0025-5416(84)90078-8 ↗
12. PETIT J. SURESH S. VASUDEVAN A. K. and MALCOLM R. C.: in ‘Aluminium—lithium alloys III’ (Conf. Proc.) (ed. Baker C. et al.) 257-262; 1986 London The Institute of Metals.
13. GLAZER J., , VERZASCONI S. L., , DALDER E. N. C., , EMIGH W. yU, R. A., , RITCHIE R. O., , and MORRIS J. W., : Adv. Cryog. Eng., 1986, 32, 397.
14. 10.1016/0036-9748(86)90100-610.1016/0036-9748(86)90100-6 ↗
15. WEBSTER D.: Metall. Trans., 1987, I8A, 2181.
16. 10.1016/S0036-9748(88)80312-010.1016/S0036-9748(88)80312-0 ↗
17. VENKATESWARA RAO K. T., and RITCHIE R. O.: Mater. Sci. Technol., 1989, this issue, 896-907.
18. 10.1007/BF0265392910.1007/BF02653929 ↗
19. 10.1007/BF0266981410.1007/BF02669814 ↗
20. HUANG J. C., and ARDELL A. J.: Mater. Sci. Technol., 1987, 3, (4), 176–188.
21. RIOJA R. J. BRETZ P. E. SAWTELL R. R. HUNT W. H. and LUDWICZAK E. A.: in ‘Aluminum alloys: their physical and mechanical properties’ (ed. Sanders T. H. and Starke E. A.); 1986 Warley W. Midlands Engineering Materials Advisory Service.
22. 10.1179/mst.1987.3.2.8110.1179/mst.1987.3.2.81 ↗
23. RADMILOVIC V., , THOMAS G., , SHIFLET G. I., , and STARKE E. A.: Scr. Metall., 1989, 23, in press.
24. MEYER P. and DUBOST B.: in ‘Aluminium—lithium alloys III’ (Conf. Proc.) (ed. Baker C. et al.) 37; 1986 London The Institute of Metals.
25. JESUS R. DE and ARDELL A. J.: in ‘Aluminum—lithium alloys’ (ed. R. Kar etal.); 1988 Metals Park OH ASM International (in press).
26. RITCHIE R. O. and YU W.: in ‘Small fatigue cracks’ (ed. Ritchie R. O. and Lankford J.) 167; 1986 Warrendale PA The Metallurgical Society of AIME.
27. 10.1016/0025-5416(85)90276-910.1016/0025-5416(85)90276-9 ↗
28. 10.1007/BF0265224210.1007/BF02652242 ↗
29. 10.1007/BF0267228510.1007/BF02672285 ↗
30. 10.1007/BF0291340310.1007/BF02913403 ↗
31. 10.1007/BF0264335010.1007/BF02643350 ↗
32. 10.1016/0025-5416(85)90065-510.1016/0025-5416(85)90065-5 ↗
33. 10.1016/0025-5416(86)90403-910.1016/0025-5416(86)90403-9 ↗
34. VASUDEVAN A. K. and DOHERTY R. D.: Acta Metall. 1987 35 1193.10.1016/0001-6160(87)90001-0 ↗
35. 10.2514/3.2860610.2514/3.28606 ↗
36. EMBURY J. D., , FETCH N. J., , WRAITH A. E., , and WRIGHT E. S.: Trans. Met. Soc. AIME, 1967, 239, 114.
37. MARKSTREIM K.: Eng. Fract. Mech. 1968 I 55.
38. 10.1016/0025-5416(88)90235-210.1016/0025-5416(88)90235-2 ↗
39. VASUDEVAN A. K. MILLER A. C. and KERSICER M. M.: in ‘Aluminium—lithium alloys II’ (Conf. Proc.) (ed. Sanders T. H. and Starke E. A.) 181; 1984 Warrendale PA The Metallurgical Society of AIME.
40. MILLER W. S. THOMAS M. P. LLOYD D. J. and CREBER D.: in ‘Aluminium—lithium alloys III’ (Conf. Proc.) (ed. Baker C. et al.) 584-594; 1986 London The Institute of Metals.
41. COOK J. and GORDON J. E.: Proc. R. Soc. 1962 A282 509.
42. 10.1007/BF0264928910.1007/BF02649289 ↗
43. HIRSCH J., , ENGLER O., , LÜCICE K., , PETERS M., , and WELPMANN K.: in Ref. 4, p. 605.
44. 10.1016/S0036-9748(88)80139-X10.1016/S0036-9748(88)80139-X ↗
45. RICE J. R. and JOHNSON M. A.: in ‘Inelastic behavior of solids’ (ed. Kanninen M. F. et al.) 641; 1970 New York McGraw-Hill.
46. 10.1016/0013-7944(77)90062-510.1016/0013-7944(77)90062-5 ↗
47. 10.1007/BF0281202210.1007/BF02812022 ↗
48. 10.1007/BF0281530510.1007/BF02815305 ↗
49. 10.1007/BF0267228610.1007/BF02672286 ↗
50. HAHN G. T. and ROSENFIELD A. R.: in ‘Applications related phenomena in titanium alloys’ ASTM STP 432 5; 1968 Philadelphia PA American Society for Testing and Materials.10.1520/STP33617S ↗
51. 10.1179/03063458179042693010.1179/030634581790426930 ↗