journal article·2026-08

Optimization of formability of silica matrix composite powder via particle size distribution model for selective fibre-laser sintering

Wenwen Liu, Shan Yao

Materials Science and Technology· Volume 42· Issue 12
Publisher page

Abstract

Composite powders consisting of silica particles, thermosetting phenolic resin (TSPF) and graphite were developed for selective fibre-laser sintering (F-SLS). Two alternative particle packing/size distribution models, such as, Andreasen model and Horsfield theory were employed in this work. The result shows all composite powders exhibit good flowability. While the grey-scale value of the powder based on Horsfield theory was smaller than that based on Andreasen model, resulting in an improvement of the laser absorption rate. F-SLS material derived from composite powders graded according to the Horsfield model achieved lower porosity and higher strength than those derived from those according to the Andreasen model, the final tensile strength being 40% higher (1.26 MPa).
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Manufacturing Process and Optimization · 3D Shape Modeling and Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Dalian University of Technology

References (33)

Show source-provided references
1. 10.1080/10426914.2022.207288710.1080/10426914.2022.2072887 ↗
2. 10.47545/etrj.2019.4.1.04910.47545/etrj.2019.4.1.049 ↗
3. 10.1007/s00170-021-07163-710.1007/s00170-021-07163-7 ↗
4. 10.1155/2022/476148110.1155/2022/4761481 ↗
5. 10.1016/j.optlastec.2021.10742510.1016/j.optlastec.2021.107425 ↗
6. Lee IS. Full densed alumina-glass composites by SLS and ceracon forging process. Met Mater 1997; 3: 203–209.
7. 10.3390/pr1004073210.3390/pr10040732 ↗
8. Martukanitz RP. A critical review of laser beam welding. In: Proceedings of Lasers and Applications in Science and Engineering San Jose CA USA. 2005 pp.11–24.10.1117/12.601655 ↗
9. 10.7567/JJAP.53.09010110.7567/JJAP.53.090101 ↗
10. 10.1007/s12540-023-01618-010.1007/s12540-023-01618-0 ↗
11. 10.1115/1.304613210.1115/1.3046132 ↗
12. 10.1007/s00170-021-07482-910.1007/s00170-021-07482-9 ↗
13. 10.1108/1355254971019183610.1108/13552549710191836 ↗
14. Xinpeng G, Jinzhi W, Guoxia F, et al. Progress on polymer material for SLS 3D printing. New Chem Mater 2020; 48: 27–31.
15. 10.1061/JGGEFK.GTENG-1097210.1061/JGGEFK.GTENG-10972 ↗
16. 10.1016/j.conbuildmat.2022.12987210.1016/j.conbuildmat.2022.129872 ↗
17. 10.1016/j.matlet.2022.13269410.1016/j.matlet.2022.132694 ↗
18. 10.1080/10298436.2018.143036510.1080/10298436.2018.1430365 ↗
19. 10.1061/(ASCE)MT.1943-5533.000083810.1061/(ASCE)MT.1943-5533.0000838 ↗
20. 10.1007/s00603-018-1719-310.1007/s00603-018-1719-3 ↗
21. 10.1016/j.cemconcomp.2012.05.00410.1016/j.cemconcomp.2012.05.004 ↗
22. 10.1016/j.ceramint.2016.12.06710.1016/j.ceramint.2016.12.067 ↗
23. 10.1016/j.cemconcomp.2023.10526710.1016/j.cemconcomp.2023.105267 ↗
24. 10.1109/TCSVT.2022.318494910.1109/TCSVT.2022.3184949 ↗
25. 10.1016/j.conbuildmat.2014.08.00210.1016/j.conbuildmat.2014.08.002 ↗
26. 10.1016/j.jqsrt.2023.10878010.1016/j.jqsrt.2023.108780 ↗
27. Lang C. Research on digital manufacturing process of centrifugal pump body based on additive manufacturing technology. M.Sc. Thesis Dalian University of Technology 2021.
28. 10.1007/s12540-022-01380-910.1007/s12540-022-01380-9 ↗
29. 10.1080/10426914.2021.188570710.1080/10426914.2021.1885707 ↗
30. 10.1007/s10035-023-01361-810.1007/s10035-023-01361-8 ↗
31. 10.1007/s10035-020-01035-910.1007/s10035-020-01035-9 ↗
32. 10.1016/j.optlastec.2003.08.01010.1016/j.optlastec.2003.08.010 ↗
33. 10.1088/2053-1591/abcc5d10.1088/2053-1591/abcc5d ↗