journal article·2025-07

Evaluation of tool rotational speed effect in Al-16Si-4Cu-10SiC composite/Al-4Cu-Mg alloy joint

Hamed Jamshidi Aval, Ivan Galvão

Materials Science and Technology· Volume 41· Issue 10
Publisher page

Abstract

This study investigated the influence of the rotational speed of the tool with a cylindrical threaded pin on the microstructure, mechanical properties and corrosion resistance of the Al-16Si-4Cu-10SiC composite/Al-4Cu-Mg alloy joint. The results show tunnel defects are formed on the advancing side in the heat input less than 121 J/mm and more than 342 J/mm. With the increase of rotational speed from 800 to 1000 rpm, the silicon particle size and the aspect ratio have decreased and increased from 5.6 ± 1.2 to 3.5 ± 1.4 µm and 0.6 to 0.8, respectively. By decreasing rotational speed from 1000 to 800 rpm, the maximum hardness (152.3 ± 0.6 HV0.1), yield strength (383 ± 6 MPa), ultimate tensile strength (469 ± 9 MPa) and corrosion rate (1.03 mm/year) were achieved.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Babol Noshirvani University of Technology

Instituto Superior de Engenharia de Lisboa (ISEL), Instituto Politécnico de Lisboa

References (51)

Show source-provided references
1. Albannai AI. Review the common defects in friction stir welding. Int J Sci Technol Res 2020; 9: 318–329.
2. 10.1016/j.cirp.2015.05.00610.1016/j.cirp.2015.05.006 ↗
3. 10.1016/j.jmst.2017.11.02910.1016/j.jmst.2017.11.029 ↗
4. 10.1080/09507116.2021.199225610.1080/09507116.2021.1992256 ↗
5. Soutis C. Aerospace engineering requirements in building with composites in Polym Compos Aerosp Ind. 2nd ed. 2020, pp. 3–22.
6. 10.1016/j.msea.2018.10.11610.1016/j.msea.2018.10.116 ↗
7. 10.1016/j.dt.2019.08.01710.1016/j.dt.2019.08.017 ↗
8. 10.1177/002199832092552810.1177/0021998320925528 ↗
9. 10.1177/0954408921100599410.1177/09544089211005994 ↗
10. 10.1007/s12633-020-00405-510.1007/s12633-020-00405-5 ↗
11. 10.1016/j.matpr.2020.02.93310.1016/j.matpr.2020.02.933 ↗
12. 10.1016/j.matdes.2013.09.06710.1016/j.matdes.2013.09.067 ↗
13. Chaluvaraju B, Afzal A, Vinnik DA, et al. Mechanical and corrosion studies of friction stir welded nano Al2O3 reinforced Al-Mg matrix composites: RSM-ANN modelling approach. Symmetry 2021; 13: 37.
14. 10.1016/j.matdes.2010.05.05510.1016/j.matdes.2010.05.055 ↗
15. Kaushik N, Singhal S. A case study of mechanical and metallurgical properties of friction stir welded AA6063 AMC. Int J Microstruct Mater Prop 2018; 13: 240–255.
16. 10.1007/s11665-021-06181-610.1007/s11665-021-06181-6 ↗
17. 10.1016/j.matchar.2018.01.05310.1016/j.matchar.2018.01.053 ↗
18. 10.1016/j.jascer.2016.04.00210.1016/j.jascer.2016.04.002 ↗
19. 10.3390/met1101006810.3390/met11010068 ↗
20. 10.1016/j.rinp.2021.10396210.1016/j.rinp.2021.103962 ↗
21. 10.1016/j.matpr.2020.03.69010.1016/j.matpr.2020.03.690 ↗
22. 10.1016/S1003-6326(19)64981-210.1016/S1003-6326(19)64981-2 ↗
23. 10.1016/j.jajp.2024.10019210.1016/j.jajp.2024.100192 ↗
24. 10.1016/j.mtcomm.2022.10450510.1016/j.mtcomm.2022.104505 ↗
25. 10.1080/02670836.2017.139397610.1080/02670836.2017.1393976 ↗
26. 10.1243/09544062JMES226710.1243/09544062JMES2267 ↗
27. 10.1016/j.msea.2019.13854010.1016/j.msea.2019.138540 ↗
28. 10.1016/j.actamat.2021.11669210.1016/j.actamat.2021.116692 ↗
29. Abbasi M, Abdollahzadeh A, Bagheri B, et al. Study on the effect of the welding environment on the dynamic recrystallization phenomenon and residual stresses during the friction stir welding process of aluminum alloy. Proc Inst Mech Eng Part L 2021; 235: 1809–1826.
30. 10.1016/j.msea.2022.14423110.1016/j.msea.2022.144231 ↗
31. 10.1007/s12540-019-00316-010.1007/s12540-019-00316-0 ↗
32. 10.1016/j.matdes.2016.09.01210.1016/j.matdes.2016.09.012 ↗
33. 10.1007/s11665-016-1927-510.1007/s11665-016-1927-5 ↗
34. 10.1016/j.msea.2021.14149910.1016/j.msea.2021.141499 ↗
35. 10.1016/j.jmrt.2023.10.09810.1016/j.jmrt.2023.10.098 ↗
36. 10.1021/am301459q10.1021/am301459q ↗
37. 10.1080/02670836.2017.140755310.1080/02670836.2017.1407553 ↗
38. 10.1007/BF0266852510.1007/BF02668525 ↗
39. 10.1016/j.jallcom.2018.02.04710.1016/j.jallcom.2018.02.047 ↗
40. 10.1016/j.msea.2016.08.06210.1016/j.msea.2016.08.062 ↗
41. 10.1016/j.jmrt.2021.05.00310.1016/j.jmrt.2021.05.003 ↗
42. 10.1016/j.msea.2019.13879710.1016/j.msea.2019.138797 ↗
43. 10.1016/j.jallcom.2021.16143310.1016/j.jallcom.2021.161433 ↗
44. 10.1016/j.jascer.2017.06.00210.1016/j.jascer.2017.06.002 ↗
45. 10.1016/S0266-3538(00)00235-910.1016/S0266-3538(00)00235-9 ↗
46. 10.1016/j.surfcoat.2018.06.05110.1016/j.surfcoat.2018.06.051 ↗
47. 10.1016/j.jallcom.2016.11.10010.1016/j.jallcom.2016.11.100 ↗
48. 10.1016/S0010-938X(98)00116-410.1016/S0010-938X(98)00116-4 ↗
49. 10.1016/j.electacta.2012.05.10610.1016/j.electacta.2012.05.106 ↗
50. 10.1016/j.corsci.2013.04.00110.1016/j.corsci.2013.04.001 ↗
51. 10.1016/j.corsci.2009.03.03010.1016/j.corsci.2009.03.030 ↗