journal article·2024-12

Effect of surface roughness and eutectic segregation on anodising of Al-Si-Cu alloys

Giulia Scampone, Giulio Timelli

Materials Science and Technology· Volume 40· Issue 17
Publisher page

Abstract

To study the influence of the surface roughness and eutectic silicon segregation on the anodising of diecast Al-Si-Cu alloys, an AlSi11Cu2(Fe) alloy was high-pressure diecast and hard anodised. The microstructure and surface topography of milled and grit-blasted regions were investigated to analyse their effect on the growth of the anodic layer. The surface mechanical properties of the anodised surfaces were also studied. The results showed how high surface roughness and silicon segregation present in the grit-blasted surface hindered the thickening of the oxide layer. After anodising, the milled surface exhibited better mechanical properties than the grit-blasted one. The wear resistance was enhanced by a thicker anodic layer, while the scratch resistance was positively affected by a lower surface roughness.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Anodic Oxide Films and Nanostructures · Corrosion Behavior and Inhibition · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Management and Engineering, University of Padova, Vicenza, Italy

Funding

European Union - NextGenerationEU

References (33)

Show source-provided references
1. 10.1533/9780857095466.10910.1533/9780857095466.109 ↗
2. 10.1007/978-3-319-58380-810.1007/978-3-319-58380-8 ↗
3. Cotell CM · 1994
4. 10.1016/j.electacta.2003.10.02410.1016/j.electacta.2003.10.024 ↗
5. 10.1016/j.surfcoat.2021.12757010.1016/j.surfcoat.2021.127570 ↗
6. Scampone G · JOM · 2023
7. Revilla RI · J Electrochem Soc · 2018 · 165
8. 10.1016/j.surfcoat.2021.12733910.1016/j.surfcoat.2021.127339 ↗
9. 10.1007/978-3-319-72177-410.1007/978-3-319-72177-4 ↗
10. 10.1149/2.1631707jes10.1149/2.1631707jes ↗
11. 10.1016/S0257-8972(02)00750-810.1016/S0257-8972(02)00750-8 ↗
12. 10.1002/adem.20210148010.1002/adem.202101480 ↗
13. 10.1016/j.mtcomm.2022.10341810.1016/j.mtcomm.2022.103418 ↗
14. 10.1007/s11661-009-9841-110.1007/s11661-009-9841-1 ↗
15. 10.1007/s11661-007-9243-110.1007/s11661-007-9243-1 ↗
16. 10.1007/s11661-014-2515-710.1007/s11661-014-2515-7 ↗
17. Campbell J · 2011
18. 10.1016/j.surfcoat.2018.07.08410.1016/j.surfcoat.2018.07.084 ↗
19. British Standards Institution (BSI). Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties. [place unknown]: BSI; 2020. Standard No. EN 1706:2020.
20. Aluservice - Product Catalogue [Internet]. Available from: http://www.aluservice.com/pdf/Aluservice_21 × 21_2012_low_02.pdf.
21. 10.1007/s13632-016-0331-810.1007/s13632-016-0331-8 ↗
22. British Standards Institution (BSI). Metallic and oxide coatings - Measurement of coating thickness - Microscopical method. [place unknown]: BSI; 2004. Standard No. EN ISO 1463:2003.
23. British Standards Institution (BSI). Paints and varnishes - Scratch test using a spring-loaded pen. [place unknown]: BSI; 2020. Standard No. EN ISO 22557:2020.
24. 10.1016/j.msea.2007.03.04410.1016/j.msea.2007.03.044 ↗
25. 10.1016/j.ijfatigue.2020.10568510.1016/j.ijfatigue.2020.105685 ↗
26. 10.1016/j.matdes.2016.04.01310.1016/j.matdes.2016.04.013 ↗
27. 10.1016/j.electacta.2004.02.03010.1016/j.electacta.2004.02.030 ↗
28. 10.1016/j.scriptamat.2005.01.00710.1016/j.scriptamat.2005.01.007 ↗
29. 10.1007/978-3-319-05894-810.1007/978-3-319-05894-8 ↗
30. Zhu B · 2019
31. 10.4028/www.scientific.net/SSP.285.3910.4028/www.scientific.net/SSP.285.39 ↗
32. 10.1016/j.rsurfi.2022.10008910.1016/j.rsurfi.2022.100089 ↗
33. Feng B · AIP Adv · 2017 · 7