Effect of cooling rates from partial solution temperature and aging on γ′ precipitation in IN792 superalloy
Source abstract
Abstract
One of the important factors affecting the microstructure of Ni base superalloys is the cooling rate from partial solution temperature; therefore, the prime purpose of the present research is to investigate the effects of this factor on some microstructural features of superalloy IN792. The results showed that by increasing the cooling rate from 5 to 160°C min−1 after partial solution treatment at 1120°C for 2 h, the size and volume fraction of primary γ′ decreased, but during the subsequent aging the volume fraction of secondary γ′ increased initially exponentially and later linearly. When high cooling rates >90°C min−1 were applied, the formation of secondary γ′ was totally suppressed. However, after aging at 845°C for a period of 24 h, the amount of secondary γ′ increased with a decelerating rate up to 60°C min−1 and then with a linear rate up to 160°C min−1. The later observation has not been reported elsewhere.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Aluminum Alloy Microstructure Properties · Advanced Materials Characterization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Center of Excellence for High Strength Alloys Technology (CEHSAT), School of Metallurgy and Materials Engineering, Iran University of Science and Technology (IUST), Narmak, Tehran, Iran
School of Metallurgy and Materials Engineering, IUST, Narmak, Tehran, Iran
IUST, Narmak, Tehran, Iran
References (17)
Show source-provided references
1. 10.1007/s12666-010-0036-710.1007/s12666-010-0036-7 ↗
2. 10.31399/asm.tb.stg2.978162708267910.31399/asm.tb.stg2.9781627082679 ↗
3. 10.1016/S0921-5093(98)00867-310.1016/S0921-5093(98)00867-3 ↗
4. 10.1016/j.jmatprotec.2004.01.00610.1016/j.jmatprotec.2004.01.006 ↗
5. 10.1016/j.jmatprotec.2005.04.02110.1016/j.jmatprotec.2005.04.021 ↗
6. 10.1016/j.msea.2004.01.02710.1016/j.msea.2004.01.027 ↗
7. Koul AK, Castillo R, Swaminathan VP, Cheruvu NS: ‘Advanced materials and coatings for combustion turbines’, Proc. ASM 1993 Materials Cong. Materials Week, ASM International, Pittsburg, PA, USA, October 1993, 17–21.
8. 10.1016/S0921-5093(97)00161-510.1016/S0921-5093(97)00161-5 ↗
9. 10.1007/BF0024101610.1007/BF00241016 ↗
10. 10.1016/j.jallcom.2007.01.09110.1016/j.jallcom.2007.01.091 ↗
11. 10.1016/S0921-5093(01)01758-010.1016/S0921-5093(01)01758-0 ↗
12. Erickson GL: ‘Metals handbook’, 10th edn, Vol. 1, 981–994; 1990, Materials Park, OH, ASM international.
13. Reed-Hill R, Abbaschian R: ‘Physical metallurgy principles’; 1994, Boston, MA, PWS Publishing Company.
14. 10.1016/j.msea.2006.02.03910.1016/j.msea.2006.02.039 ↗
15. Porter DA, Easterling KE: ‘Phase transformations in metals and alloys’, Vol. 5, 290–300; 1983, Berkshire, Van Nostrand Reinhold Co. Ltd.
16. 10.1016/0025-5416(84)90056-910.1016/0025-5416(84)90056-9 ↗
17. 10.1016/S1359-6454(02)00042-310.1016/S1359-6454(02)00042-3 ↗