journal article·2017-09

Effects of alloying elements and cooling rates on the high-strength pearlite steels

Mingming Wang, Fucheng Zhang, Zhinan Yang

Materials Science and Technology· Volume 33· Issue 14
Publisher page

Abstract

The effects of the alloying elements of Cr, Mn and the cooling rates after hot deformation on the microstructures and mechanical properties of pearlite steels were studied. Results show that increasing Cr and decreasing Mn significantly increase the eutectoid transformation temperature of steel. The grain sizes of prior austenite of the steels after hot deformation are ∼12 µm. However, the high-Cr–low-Mn steel exhibits a finer interlamellar spacing and some better mechanical properties than that of the high-Mn–low-Cr steel. A full pearlite microstructure with an interlamellar spacing of 97 nm was obtained on the former steel, which exhibits a hardness of HRC49, a tensile strength of 1700 MPa and an elongation of 19%.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Magnetic Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao, China

National Engineering Research Center for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao, China

Funding

National Natural Science Foundation of China

References (23)

Show source-provided references
1. 10.1007/BF0264469410.1007/BF02644694 ↗
2. Zener C · Trans AIME · 1946 · 167 · 550
3. 10.1016/j.scriptamat.2012.03.01910.1016/j.scriptamat.2012.03.019 ↗
4. 10.1016/j.matdes.2013.10.06210.1016/j.matdes.2013.10.062 ↗
5. 10.1016/j.msea.2005.05.05110.1016/j.msea.2005.05.051 ↗
6. 10.3221/IGF-ESIS.30.5110.3221/IGF-ESIS.30.51 ↗
7. 10.2355/isijinternational.43.182110.2355/isijinternational.43.1821 ↗
8. 10.1016/j.scriptamat.2004.11.01510.1016/j.scriptamat.2004.11.015 ↗
9. 10.2355/tetsutohagane.101.22110.2355/tetsutohagane.101.221 ↗
10. 10.1016/j.actamat.2013.10.03410.1016/j.actamat.2013.10.034 ↗
11. 10.1007/s11661-010-0233-310.1007/s11661-010-0233-3 ↗
12. 10.1007/BF0264555010.1007/BF02645550 ↗
13. 10.1016/S1044-5803(00)00056-510.1016/S1044-5803(00)00056-5 ↗
14. 10.1016/S1359-6462(99)00200-610.1016/S1359-6462(99)00200-6 ↗
15. 10.1016/S1044-5803(00)00113-310.1016/S1044-5803(00)00113-3 ↗
16. 10.1016/0001-6160(78)90156-610.1016/0001-6160(78)90156-6 ↗
17. 10.1016/j.msea.2015.02.04010.1016/j.msea.2015.02.040 ↗
18. 10.2355/isijinternational.ISIJINT-2015-10210.2355/isijinternational.ISIJINT-2015-102 ↗
19. 10.1179/02670830322500831010.1179/026708303225008310 ↗
20. 10.1016/S1359-6462(01)01016-810.1016/S1359-6462(01)01016-8 ↗
21. 10.1007/BF0302753710.1007/BF03027537 ↗
22. 10.1016/j.matdes.2015.12.09610.1016/j.matdes.2015.12.096 ↗
23. 10.1179/02670830322500437810.1179/026708303225004378 ↗