journal article·2011-01

Mechanical performance of three thickness resistance spot welded low carbon steel

A. Tavasolizadeh, S. P. H. Marashi, M. Pouranvari

Materials Science and Technology· Volume 27· Issue 1
Publisher page

Abstract

Resistance spot welding is the dominant process for joining sheet metals in automotive industry. Despite the application of three thickness resistance spot welds in this industry, present guidelines and recommendations are limited to two thickness spot welds. Study towards better understanding of weld nugget growth and mechanical properties is the first step to understanding the welding behaviour and developing proper guidelines for the three thickness resistance spot welding. In this paper, weld nugget growth, mechanical performance and failure behaviour of three thickness low carbon steel resistance spot welds are investigated. Macrostrcutural and microstructural investigations, microhardness tests and quasi-static tensile–shear tests were conducted. Mechanical performance of the joint was described in terms of peak load, energy absorption and failure mode. In order to understand the failure mechanism, micrographs of the cross-sections of the spot welded joints during and after tensile–shear are examined by optical microscopy. Unlike two thickness resistance spot welded joint, weld nugget was formed in the geometrical centre of the joint (i.e. centre of the middle sheet). Weld nugget size along sheet/sheet interface was greater than that of along geometrical centre of the joint. Increasing welding time leads to increases in peak load and energy absorption of the joint and transition of interfacial failure mode to pullout failure mode, primarily due to the enlargement of weld nugget size along sheet/sheet interface.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Metal and Thin Film Mechanics · Electrical Contact Performance and Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Mining and Metallurgical Engineering Department Amirkabir University of Technology, Tehran, Iran

Materials and Metallurgical Engineering Department School of Engineering, Islamic Azad University, Dezful Branch, Dezful, Iran

References (13)

Show source-provided references
1. 10.1179/09506600422501052310.1179/095066004225010523 ↗
2. Jung W. W., Kwon Y. D., and Kang S. S. ‘Selecting the spot welding condition of multi-layer vehicle structure’, SAE technical paper, SAE, Detroit, Michigan, SAE 970083.
3. 10.1179/13621710222500149410.1179/136217102225001494 ↗
4. 10.1016/S0924-0136(03)00447-310.1016/S0924-0136(03)00447-3 ↗
5. 10.1016/j.ijfatigue.2006.07.01610.1016/j.ijfatigue.2006.07.016 ↗
6. Coon T., Elliott A., Joaquin A., Koganti R., Wexler A., Bhatnagar R., and Lalam S. ‘Resistance spot weldability of three metal stack dual phase 600 hot-dipped galvanized steel’, SAE technical paper, SAE, Detroit, Michigan, SAE 2007-01-1363.10.4271/2007-01-1363 ↗
7. Zhou M. · Weld. J. · 2003 · 82 · 72s
8. Hutchings C. L. ‘Weld nugget growth when resistance spot welding two and three thickness uncoated low carbon steel sheets’, PhD thesis, University of Wales, Swansea, 2000.
9. Gould J. E. · Weld J. · 2006 · 86 · 111s
10. Pouanvari M. · Sci. Technol. Weld. Join. · 2007 · 12 · 223
11. 10.1016/j.msea.2007.07.00710.1016/j.msea.2007.07.007 ↗
12. 10.1179/174328408X26241810.1179/174328408X262418 ↗
13. Zuniga S., and Sheppard S. D.: in ‘Fatigue and fracture mechanics’, (ed. Piascik R. S. et al.), Vol. 27, ASTM STP 1296, 469–489; 1997, Philadelphia, PA, ASTM.10.1520/STP16249S ↗