journal article·2012-05

Alloy selection for in mould inoculation to control chill width in ductile iron

S S Ojo, I Riposan

Materials Science and Technology· Volume 28· Issue 5
Publisher page

Abstract

The relative performance of six FeSi based inoculants was tested for of ductile iron chill width control using in the mould inoculation after FeSiCaMgRE treatment. In the prevailing solidification conditions (W3 chill wedge, ASTM A367-85, resin sand mould), Sr–FeSi alloys did not perform well, but had a 15–30 benefit from preconditioning with Al,Zr,Ca–FeSi. Ba,Ca–FeSi alloy had the lowest efficiency, without any benefit from preconditioning. The best inoculant performance is achieved using a complex inoculant chemistry (Ca,RE,S,O–FeSi), while the Ca,Zr–FeSi alloy was the second rated inoculant, with important benefits from preconditioning in both cases. Al,Zr,Ca–FeSi preconditioning of the base iron before Ca–FeSi inoculation showed better performance than an inoculation only treatment using the same active elements (Ca,Zr,Al–FeSi alloy).
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metallurgical Processes and Thermodynamics · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

The Federal University of Technology, Akure, Nigeria

Department of Materials Science and Engineering, Politehnica University of Bucharest, 313 Spl. Independentei, RO-060042, Bucharest, Romania

References (19)

Show source-provided references
1. 10.1179/026708309X1249554850862610.1179/026708309X12495548508626 ↗
2. 10.1179/03071697480328781610.1179/030716974803287816 ↗
3. Jacobs MH, Law TJ, Melford DA, Stowell MJ: Met. Technol., Mar. 1976, 98–108.10.1179/030716976803391610 ↗
4. Skaland T: ‘A model for the graphite formation in ductile cast iron’, PhD thesis, The University of Trondheim, NTH, Norway, 1992.
5. Skaland T: Proc. AFS Metalcasting Cong. 2001, AFS, Paper 01-078
6. Modern Cast., Dec. 2001, 43-45.10.1007/BF02763383 ↗
7. Skaland T: Proc. AFS Cast Iron Inoc. Conf. Schaumburg, IL, USA, September 2005, AFS, 13–30.
8. Skaland T: Proc. 2003 Keith Millis Symp. on ‘Ductile cast iron’, Hilton Head Island, SC, USA, October 2003, DIS/AFS, 61–69; Proc. 66th World Foundry Cong., Istanbul, Turkey, September 2004, WFO,
9. ‘Selection of inoculants for ductile cast iron’, Technical information no. 16, ELKEM Foundry Products, www.foundry.elkem.com
10. 10.1179/026708310X1266841553364910.1179/026708310X12668415533649 ↗
11. Suarez R · Revista de Metalurgia · 2009 · 45 · 33910.3989/revmetalm.0840 ↗
12. Fras E · Int. Foundry Res. · 2010 · 62 · 12
13. 10.1007/s11663-009-9289-010.1007/s11663-009-9289-0 ↗
14. ‘Preseed preconditioner booklet’, ELKEM Foundry Products Division, www.foundry.elkem.com
15. Ojo SS: ‘Influence of inoculation on thin wall ductile iron casting’, PhD thesis, Politehnica University of Bucharest, Bucharest, Romania, 2009.
16. Riposan I, Chisamera M, Stan S, White D: AFS Trans. 2007, 115, 423–433; Modern Cast., May 2008, http://www.moderncasting.com/images/stories/webonly/residual_aluminum.pdf
17. Stan S · AFS Trans. · 2010 · 118 · 295
18. 10.1007/s11665-010-9640-210.1007/s11665-010-9640-2 ↗
19. Riposan I · Mater. Sci. Technol. · 2008 · 24 · 57810.1179/174328408X298842 ↗