journal article·2018-08

Influence of post-weld heat treatment on microstructure and adhesion of Ti/Cu composite

Feifan Chen, Wei Wang, Kang Wang, Pofeng Ho, Han Li, Xi Huang, Weijie Chen

Materials Science and Technology· Volume 34· Issue 12
Publisher page

Abstract

It is well known that brittle interfacial intermetallics are typically present in laminated composites and degrade their mechanical performance. To investigate the relationship between intermetallics and mechanical properties, Ti/Cu-laminated composite plates prepared by explosive welding were studied with different heat treatments. A transition layer containing four zones of intermetallic phases, Cu 4 Ti, Cu 4 Ti 3 , CuTi, and CuTi 2 , was found at the interface between Ti and Cu after explosive welding. The intermetallics became thicker as the temperature of the heat treatment increased, especially for the CuTi phase. The sample treated at 473 K exhibited the highest bonding strength of 199.7 MPa, which was attributed to the elimination of residual stress during the welding and the diffusion of copper to improve interfacial bonding.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Midea Group, Research Institute of Small Domestic Appliance Division, Foshan, People's Republic of China

School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, People's Republic of China

Funding

Midea Group

References (33)

Show source-provided references
1. 10.1016/j.scriptamat.2010.09.00610.1016/j.scriptamat.2010.09.006 ↗
2. 10.1016/j.matchar.2016.10.02410.1016/j.matchar.2016.10.024 ↗
3. 10.1016/j.matchar.2017.01.02210.1016/j.matchar.2017.01.022 ↗
4. 10.1016/j.msea.2006.09.18410.1016/j.msea.2006.09.184 ↗
5. 10.1016/j.msea.2007.08.07610.1016/j.msea.2007.08.076 ↗
6. 10.1016/S0925-8388(03)00392-X10.1016/S0925-8388(03)00392-X ↗
7. 10.1016/j.compositesb.2011.04.04510.1016/j.compositesb.2011.04.045 ↗
8. 10.1016/j.matchar.2017.10.00910.1016/j.matchar.2017.10.009 ↗
9. 10.1016/j.matdes.2016.04.03710.1016/j.matdes.2016.04.037 ↗
10. 10.1016/j.matdes.2015.11.08710.1016/j.matdes.2015.11.087 ↗
11. 10.1016/j.jmatprotec.2005.02.26410.1016/j.jmatprotec.2005.02.264 ↗
12. 10.1016/j.matdes.2012.01.02610.1016/j.matdes.2012.01.026 ↗
13. 10.1016/j.matdes.2015.04.00310.1016/j.matdes.2015.04.003 ↗
14. 10.1016/j.jmatprotec.2008.06.01410.1016/j.jmatprotec.2008.06.014 ↗
15. 10.1016/j.jallcom.2004.07.05710.1016/j.jallcom.2004.07.057 ↗
16. Qin L · J Mater Eng Perform · 2017 · 26 · 1
17. 10.1007/s11665-016-1978-710.1007/s11665-016-1978-7 ↗
18. 10.1007/s11661-013-2144-610.1007/s11661-013-2144-6 ↗
19. 10.1557/JMR.2008.026910.1557/JMR.2008.0269 ↗
20. 10.1007/BF0077554310.1007/BF00775543 ↗
21. Anon. Standard test method for strength properties of adhesives in shear by tension loading of single-lap-joint laminated assemblies. ASTM.
22. Li D. · Mater Sci Eng Powder Metall · 2007 · 12 · 25
23. 10.1007/s11664-997-0268-410.1007/s11664-997-0268-4 ↗
24. 10.1007/BF0265136510.1007/BF02651365 ↗
25. 10.1016/j.calphad.2010.12.00610.1016/j.calphad.2010.12.006 ↗
26. 10.1016/j.matlet.2007.12.06710.1016/j.matlet.2007.12.067 ↗
27. 10.1063/1.169956310.1063/1.1699563 ↗
28. 10.1016/S1359-6454(96)00325-410.1016/S1359-6454(96)00325-4 ↗
29. 10.3139/146.11068510.3139/146.110685 ↗
30. 10.1115/1.55618910.1115/1.556189 ↗
31. 10.1016/j.jallcom.2008.05.07010.1016/j.jallcom.2008.05.070 ↗
32. 10.1007/s11661-005-0138-810.1007/s11661-005-0138-8 ↗
33. 10.1016/S0925-8388(01)00872-610.1016/S0925-8388(01)00872-6 ↗