Influence of directionality on strength and impact behaviour of high strength steels
Source abstract
Abstract
The directionality of the strength and impact behaviour of control rolled 110 grade high strength steel has been examined. Tensile specimens tested along the rolling direction were found to give strengths of ∼60 MPa lower than when tested transversely in the rolling direction. Charpy V notch impact samples, in contrast, gave lower impact transition temperatures when taken in the rolling direction (35°C lower). The difference in strength between the two directions is believed to be mainly as a result of the strong texture produced on control rolling. The difference in impact behaviour is due to the more severe fissuring on the fracture surface of the longitudinally tested specimens. Fissuring is more marked on the longitudinally tested sample because of the greater grain elongation in that direction, the initial fracture path being along the grain boundaries.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Fatigue and fracture mechanics · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
CB&1 Lummus, Paddington, UK
Tata Steel R, D & T, Rotherham, UK
City UniversityLondon, UK
References (22)
Show source-provided references
1. 10.1179/174328407X16122210.1179/174328407X161222 ↗
2. 10.1179/174328407X16880110.1179/174328407X168801 ↗
3. 10.1179/174367507X24737710.1179/174367507X247377 ↗
4. Maina E, Mintz B: ‘The influence of P and S on fissure formation in steels’, Proc. 3rd Int. Conf. on ‘Thermomechanical processing of steels’, Padua, Italy, September 2008. Paper 45, CD-Rom in session “Microstructural Control in Phase Transformation and precipitation’ ISBN 88-85298-66-4, AIM (Associazione Italiano di Metallurgia).
5. Little JH · Met. Soc. London · 1973 · 1 · 80
6. Bourell D · Metall. Trans. A · 1983 · 14 · 2847
7. Speich GR, Dablowski DS: in ‘Hot deformation of austenite’, (ed. , Balance J, ed), 557–597; 1977, New York, AIME.
8. 10.1179/mt.1978.5.1.3710.1179/mt.1978.5.1.37 ↗
9. 10.1007/BF0264384110.1007/BF02643841 ↗
10. 10.1179/03071697480328811210.1179/030716974803288112 ↗
11. 10.1179/03071698080328723310.1179/030716980803287233 ↗
12. 10.1179/mst.1988.4.8.71910.1179/mst.1988.4.8.719 ↗
13. Duliu D, Gouch A: ‘The microstructure and design of alloys’, Vol. 1, 70; 1973, London, The Iron and Steel Inst.
14. Mintz B, Morrison WB, Welch PI, Davies GJ: in ‘Texture of materials’, (ed. , Gottstein G, Lucke K, ed), Vol. 2, 465; 1978, Berlin, Springer-Verlag.
15. Freier K, Vlad CM, Kugler J, Feldman U: Proc. Conf. on ‘HSLA steels technology and applications’, Philadelphia, PA, USA, October 1983, ASM, 733.
16. Rittman R, Freier K: Nb Science and Technology Cong. Proc. Int. Symp. on ‘Niobium’, Orlando, FL, USA, December 2001, 571–586.
17. 10.1007/BF0264282310.1007/BF02642823 ↗
18. Maina E, BanerjeeJR, Mintz B: ‘Influence of processing route and composition on the strength and impact behaviour of grade 110 high strength steel’, Proc. 2nd Int. Conf. on ‘Super high strength steels’, Peschiera del Garda, Italy, October 2010, Associazione Italiana di Metallurgia.
19. Maina EM., Thesis PhD. Oct.2008, City University, School of Engineering and Mathematical Sciences.
20. 10.2355/isijinternational.34.92710.2355/isijinternational.34.927 ↗
21. 10.1179/03071697780329251010.1179/030716977803292510 ↗
22. Rosenfield AR · Trans. ASM · 1966 · 59 · 962