journal article·2011-12

Microstructural characterisation of deformation behaviour of nickel base superalloy IN625

P Behjati, S Asgari

Materials Science and Technology· Volume 27· Issue 12
Publisher page

Abstract

Simple compression and microscopy techniques were employed to characterise the microstructural origin of the deformation behaviour of nickel base superalloy IN625 during large strain testing. The alloy exhibited a four-stage strain hardening response similar to that previously reported for low stacking fault energy face centred cubic alloys. At strains lower than about −0·06 (stage A), a falling regime of the hardening rate was observed. This stage was followed by a second stage (stage B) of slow increasing hardening rate, which was found to be coincident with the formation of Lomer–Cottrell locks. The second falling regime of strain hardening (stage C) was seen in the strain range of −0·25 to −0·65. The occurrence of this stage was attributed to the increasing ease of dislocation cross-slip with increasing strain and consequently to the decreasing Lomer–Cottrell lock efficiency in hindering dislocation movement. Beyond a strain of −0·65, a final slightly constant hardening regime (stage D) was developed. The initiation of this stage was concurrent with the onset of deformation twinning in the microstructure.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and mechanical properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Engineering Isfahan University of Technology, Isfahan 14156-2752, Iran

Department of Materials Science and Engineering Sharif University of Technology, Tehran 11365-8639, Iran

References (18)

Show source-provided references
1. Roberts WN · Trans. TMS-AIME · 1964 · 230 · 372
2. Raghavan KS · Trans. TMS-AIME · 1969 · 245 · 1569
3. 10.1007/s11661-997-0109-310.1007/s11661-997-0109-3 ↗
4. 10.1016/S0924-0136(01)00983-910.1016/S0924-0136(01)00983-9 ↗
5. 10.1016/j.jmatprotec.2004.04.28010.1016/j.jmatprotec.2004.04.280 ↗
6. 10.1007/s11661-007-9356-610.1007/s11661-007-9356-6 ↗
7. Eiselstein HL, Tillack DJ: ‘Superalloys 718, 625 and various derivatives’, 1–14; 1991, Warrendale, PA, TMS.10.7449/1991/Superalloys_1991_1_14 ↗
8. 10.1007/BF0303836910.1007/BF03038369 ↗
9. Behjati P: ‘Strain hardening mechanisms in superalloy IN625’, MS thesis, Sharif University of Technology, Tehran, Iran, 2005.
10. 10.1016/0956-7151(90)90126-210.1016/0956-7151(90)90126-2 ↗
11. Hull D, Bacon DJ: ‘Introduction to dislocations’, 4th edn; 2001, London, Butterworth-Heinemann.10.1016/B978-075064681-9/50002-X ↗
12. 10.1016/0001-6160(84)90034-810.1016/0001-6160(84)90034-8 ↗
13. 10.1016/0001-6160(89)90143-010.1016/0001-6160(89)90143-0 ↗
14. Kalidindi · Int. J. Plast. · 2001 · 17 · 1265
15. 10.1016/0001-6160(78)90170-010.1016/0001-6160(78)90170-0 ↗
16. 10.1007/BF0264853610.1007/BF02648536 ↗
17. 10.1016/0079-6425(94)00007-710.1016/0079-6425(94)00007-7 ↗
18. 10.1007/s11661-999-0272-910.1007/s11661-999-0272-9 ↗