journal article·2018-01

Effects of intense cooling on microstructure and properties of friction-stir-welded Ti–6Al–4V alloy

Zhenlei Liu, Yue Wang, Shude Ji, Zhengwei Li

Materials Science and Technology· Volume 34· Issue 2
Publisher page

Abstract

Friction stir welding (FSW) was used to join Ti–6Al–4V alloy in air and under intense cooling conditions. The results show that the application of liquid nitrogen is beneficial in decreasing the peak temperature and in reducing the extent of the high-temperature region during welding, leading to a smaller stir zone (SZ). Intense cooling can lead to refined and homogeneous grains in the SZ, resulting in increased microhardness. The FSW joint produced with intense cooling had a tensile strength of 1020 MPa, which is nearly equivalent to that of the base material and is up to 2.6% higher than for the air-cooled joint. The fractographs for both types of joint were characterised by dimples, indicating that the fractures were ductile.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Corrosion Behavior and Inhibition · MXene and MAX Phase Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Aerospace Engineering, Shenyang Aerospace University, Shenyang, PR China

State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin, PR China

References (32)

Show source-provided references
1. 10.1080/02670836.2016.122600710.1080/02670836.2016.1226007 ↗
2. Fall A · Int J Adv Manuf Technol · 2016 · 1
3. 10.1016/j.matchemphys.2005.09.01910.1016/j.matchemphys.2005.09.019 ↗
4. 10.1080/02670836.2015.111028110.1080/02670836.2015.1110281 ↗
5. 10.1179/026708306X8151310.1179/026708306X81513 ↗
6. 10.1016/j.matdes.2015.06.10310.1016/j.matdes.2015.06.103 ↗
7. 10.1080/02670836.2016.118075210.1080/02670836.2016.1180752 ↗
8. 10.1007/s00170-011-3427-y10.1007/s00170-011-3427-y ↗
9. 10.1080/02670836.2016.123706510.1080/02670836.2016.1237065 ↗
10. 10.1179/1743284713Y.000000038910.1179/1743284713Y.0000000389 ↗
11. 10.1016/j.matchar.2015.06.02510.1016/j.matchar.2015.06.025 ↗
12. 10.1016/j.matdes.2016.10.01210.1016/j.matdes.2016.10.012 ↗
13. 10.1016/j.matlet.2016.10.03210.1016/j.matlet.2016.10.032 ↗
14. 10.1007/s11661-011-0606-210.1007/s11661-011-0606-2 ↗
15. 10.1179/1362171815Y.000000004310.1179/1362171815Y.0000000043 ↗
16. 10.1007/s00170-015-6906-810.1007/s00170-015-6906-8 ↗
17. 10.1179/1362171811Y.000000002410.1179/1362171811Y.0000000024 ↗
18. 10.1186/s40712-016-0058-y10.1186/s40712-016-0058-y ↗
19. 10.1007/s11665-010-9787-x10.1007/s11665-010-9787-x ↗
20. 10.1016/j.jmst.2017.01.01610.1016/j.jmst.2017.01.016 ↗
21. Garg T · Int Rev Appl Eng Res · 2014 · 4 · 165
22. Stewart WC. Feasibility of Underwater Friction Stir Welding of HY-80 Steel. Monterey California Naval Postgraduate School, 2011.
23. 10.1179/1362171815Y.000000004210.1179/1362171815Y.0000000042 ↗
24. 10.1080/02670836.2017.132086110.1080/02670836.2017.1320861 ↗
25. 10.1179/1362171813Y.000000012810.1179/1362171813Y.0000000128 ↗
26. 10.1515/htmp-2015-017810.1515/htmp-2015-0178 ↗
27. Liu HJ · Indian J Eng Mater S · 2014 · 21 · 557
28. 10.1016/j.jmatprotec.2015.09.04110.1016/j.jmatprotec.2015.09.041 ↗
29. 10.1016/j.matdes.2011.06.02110.1016/j.matdes.2011.06.021 ↗
30. 10.1016/j.msea.2007.08.05110.1016/j.msea.2007.08.051 ↗
31. 10.1016/j.matdes.2010.01.02310.1016/j.matdes.2010.01.023 ↗
32. 10.1515/htmp-2016-001210.1515/htmp-2016-0012 ↗