journal article·2016-09

Characterisation of residual stresses in heat treated, high strength aluminium alloy extrusions

M. D. Olson, J. S. Robinson, R. C. Wimpory, M. R. Hill

Materials Science and Technology· Volume 32· Issue 14
Publisher page

Abstract

Residual stresses were measured in rectilinear aluminium bars quenched using an aqueous polyoxyethylene glycol (PAG) solution or cold-water. Residual stresses were measured with neutron diffraction and a superposition-based method using mechanical strain release measurements. Three orthogonal stress components were measured along two transverse lines using neutron diffraction. The longitudinal residual stresses were mapped over a transverse cross-section using the contour technique. A primary slice removal technique mapped three orthogonal residual stresses over a transverse cross-section in the PAG extrusion. Residual stresses were found to vary from biaxial compressive in the part boundaries to triaxial tensile in the interiors. There was close correlation between the neutron diffraction and mechanical strain release techniques. PAG quenching demonstrated lower residual stresses. This paper is part of a Themed Issue on Measurement, modelling and mitigation of residual stress.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Hill Engineering, LLC, 3035 Prospect Park, Rancho Cordova, CA, USA

Department of Mechanical, Aeronautical and Biomedical Engineering, University of Limerick, Limerick, Ireland

Helmholtz-Zentrum Berlin for Materials and Energy, Hahn Meitner Platz 1, Berlin, Germany

Department of Mechanical and Aerospace Engineering, University of California, One Shields Avenue, Davis, CA, USA

Funding

EU Seventh Framework · U.S. Air Force

References (38)

Show source-provided references
1. 10.1051/metal:200415710.1051/metal:2004157 ↗
2. Polmear I. J. · Mat. Forum · 2004 · 28 · 1
3. 10.1533/9780857090256.3.74710.1533/9780857090256.3.747 ↗
4. 10.1016/j.matdes.2013.12.00210.1016/j.matdes.2013.12.002 ↗
5. 10.1007/978-94-011-0685-6_110.1007/978-94-011-0685-6_1 ↗
6. 10.1016/B978-075066371-7/50007-410.1016/B978-075066371-7/50007-4 ↗
7. 10.1111/str.1209110.1111/str.12091 ↗
8. Totten G. E., and Mackenzie D. S. ‘Aluminum quenching technology: a review’, Mat. Sci. Forum, 2000, 331-337, 589–594.10.4028/www.scientific.net/MSF.331-337.589 ↗
9. Bates C. E. · Heat Treat. Met. · 1988 · 15 · 89
10. Croucher T. · 2009
11. Totten G. E. · 1997 · 163
12. 10.1007/s11665-015-1505-210.1007/s11665-015-1505-2 ↗
13. Cudd R. L. ‘An assessment of UCON quenchant “A” with particular reference to its possible use in the heat treatment of aluminium alloy forgings’, SX.5577, High Duty Alloys Ltd., Slough, Buckinghamshire, UK, 1969.
14. Senatorova O. G., Sidelnikov V. V., Mihailova I. F., Fridlyander I. N., Bedarev A. S., Spector J. I., and Tihonova L. A. ‘Low distortion quenching of aluminium alloys in polymer medium’, in ‘Aluminum alloys 2002: their physical and mechanical properties Pts 1–3’, 1659–1664; 2002, Uetikon-Zuerich, Switzerland, Trans Tech Publications.10.4028/www.scientific.net/MSF.396-402.1659 ↗
15. 10.1007/s11340-015-0013-510.1007/s11340-015-0013-5 ↗
16. 10.1115/1.402992710.1115/1.4029927 ↗
17. SAE · 2015
18. Robinson J. S., Truman C. E., Pirling T., and Panzner T. ‘Cold compression of the aluminium alloy 7075 and associated {311} peak broadening’, Mechanical stress evaluation by neutrons and synchrotron radiation (MECA SENS VIII), Grenoble, France, 2015, Trans Tech Publications Ltd.
19. 10.1002/9781118402832.ch510.1002/9781118402832.ch5 ↗
20. 10.1016/j.msea.2015.07.01810.1016/j.msea.2015.07.018 ↗
21. 'MMPDS-04 : Metallic materials properties development and standardization (MMPDS)’; 2008, [Washington, D.C.] : Federal Aviation Administration; [Columbus, Ohio] : Battelle Memorial Institute [distributor], [2008] ©2008.
22. 10.1002/9781118402832.ch410.1002/9781118402832.ch4 ↗
23. 10.1115/1.220495210.1115/1.2204952 ↗
24. 10.1179/1743284710Y.000000002910.1179/1743284710Y.0000000029 ↗
25. IS0/TTA3: ‘Polycrystalline materials – Determination of residual stresses by neutron diffraction’, IS0/TTA3, International standardisation organisation, 2001.
26. D. C. I. T. 21432: ‘Non-destructive testing. Standard test method for determining of residual stresses by neutron diffraction’, DD CEN ISO/TS 21432, British Standards Institute, 2005.
27. Hutchings M. T. · Introduction to the characterisation of residual stress by neutron diffraction · 2005 · 424
28. 10.1177/095440541246523210.1177/0954405412465232 ↗
29. Prime M. B., Newborn M. A., and Balog J. A. ‘Quenching and cold-work residual stresses in aluminium hand forgings: contour method measurement and FEM prediction’, THERMEC'2003: Processing & Manufacturing of Advanced Materials, Madrid, Spain, July 7–11, 2003, 2003.
30. Walker D. M. · Adv. Mater. Process. · 2002 · 160 · 57
31. 10.1016/j.jmatprotec.2006.02.00710.1016/j.jmatprotec.2006.02.007 ↗
32. Croucher T. R. · Heat Treat. · 1980 · 12 · 34
33. 10.1179/1743284711Y.000000006310.1179/1743284711Y.0000000063 ↗
34. Brandes E. A. · 2013
35. 10.1002/mawe.1996027101010.1002/mawe.19960271010 ↗
36. 10.1016/S1359-6454(97)00369-810.1016/S1359-6454(97)00369-8 ↗
37. 10.1016/j.actamat.2006.04.03410.1016/j.actamat.2006.04.034 ↗
38. Davies J. R. · 696